fixyourownprinter.com
  Home    Reference    Forums  
  Printer Repair | Laser | InkJet | Chat | SearchSign In | Sign Up  

Canon ix4000 reset warning lights.

Post to this thread   Post a new message thread

Canon ix4000 reset warning lights. by ashflat (11/1/08 9:00 PM) reply + / -
Hi all,
I have a new Canon ix4000 which for the first time I have removed the ink tanks, drilled a small hole, refilled, resealed and replaced. Now I have these red lights blinking at me. What to do????

I have had a Canon i865 for over 4 years which I have been doing the same as above without a single problem. I note in another forum :- http://www.fixyourownprinter.com/forums/inkjet/41348
that people are having problems with their Canon Pixma IP1000 Waste Ink Full warning lights, and I was wondering if the same method would fix this problem???
In anticipation,
Ashflat.



Re: Canon ix4000 reset warning lights. by scmedan (11/2/08 8:22 PM) reply + / -
Maybe this link will help you http://slayo.com/service-mode-canon-pixma-ix5000-ix4000-printers.html


Re: Canon ix4000 reset warning lights. by Anonymous (8/22/09 3:32 AM) reply + / -
To reset counter Canon PIXMA iX4000 or iX5000 you have to enter to service mode. Procedure to enter to service mode on Canon PIXMA iX4000 or iX5000 is as following :

1.Connect the Canon PIXMA iX5000 or iX4000 printer to the power cord. ( note : If the automatic power-on function is enabled in the printer, the printer enters the service mode for the first time, but it will never enter the service mode if the printer is turned off by the Power button. This is because the printer remains to be turned on internally if the power is turned off by the Power button. To prevent this, disconnection of the power cord is required before starting the printer in the service mode ) .
2.With the Canon PIXMA iX5000 or iX4000 printer powered off, while pressing the Resume/Cancel button, press and hold the Power button. (note : Doní»t release the buttons. The Power LED lights in green to indicate that a function is selectable.)
3.While holding the Power button, release Resume/Cancel button. (Doní»t release the Power button.)
4.While holding the Power button, press Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons.
5.When the Power LED lights in green, press the Resume/Cancel button 4 times to reset waste ink counter in the Canon Pixma iX5000 / iX4000. (note : If the Power LED does not light in green the printer does not enter the service mode, disconnect the power cord and plug it again. Then start from step 1 to start the printer in the service mode again).
6.At the end of the service mode, press the Power button. The paper lifting plate of the sheet feed unit will be raised.
Note :

Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.
Other specified number of time(s) according to the function listed in the table below.

Time(s) LED indication Function Remarks
0 times Green (Power) Power off
1 time Orange (Alarm) Service test print
2 times Green (Power) EEPROM information print
3 times Orange (Alarm) EEPROM initialization
4 times Green (Power) Waste ink counter resetting
5 times Orange (Alarm) Destination settings
6 times Green (Power) Print head deep cleaning (Cleaning of both black and color)



Re: Canon ix4000 reset warning lights. by jammy (12/1/10 12:53 PM) reply + / -
Hi all,
I used a Canon ix4000,my problem is after refilled my catridge tank and replaced,but my printer status show "the following ink cannot be corretly detected"..but i will used a same tank and colour..

i also try used reset method "4 times Green (Power) Waste ink counter resetting " but alarm LED still on blinked..

So everybody help me solve this problem..

TQ.




Re: Canon ix4000 reset warning lights. by bussines blog (4/22/11 9:20 AM) reply + / -
thk buat share ajah


Re: Canon ix4000 reset warning lights. by ThanZawOo (4/28/11 10:37 AM) reply + / -
error 5C00


Re: Canon ix4000 reset warning lights. by lid (3/17/13 10:54 AM) reply + / -
both led green & green blink


Post to this thread:

User:
Email:
Notify me if someone responds

Icon:            
Subject:
Message:



© 2012 fixyourownprinter.com, All posts belong to their respective posters