dante--2 things. If the toner cart says "empty", and is not, you can get a little more life out of it by replacing the fuse at eh lead edge, to the left on the cart. Use a .1A (100mA) 250V fuse. It blows upon insertion into the printer and counts down. Good luck. Any questions, you may email me as well. :-)PCRMike
Re: how to reset samsung scx 4521f by Anonymous (1/11/07 12:09 PM) reply
Then it is a starter cartridge sir. The first toner in those only goes for about 800-1K pages, and actually runs out of toner. It is not a pop-and-fill type toner either. Your best bet is buy a replacement, and when you go to put it in, look at it, see the fuse, buy one like it and after it says out, pop it in for the rest of the toner life. :-)PCRMike
Re: how to reset samsung scx 4521f by gelsystem (2/16/07 9:23 PM) reply
thanks pcrmike............!!!! so i think, i have not to take it off for little-atomic-pieces...:) i filled it -the startertoner- it works, only its always crimes: iam empty!!!!- but i do not mind
Re: how to reset samsung scx 4521f by Anonymous (5/23/07 11:36 PM) reply
1. Press MENU # 1 9 3 4 in sequence rapidly. The LCD panel should now display TECH. 2. Press MENU, and then press ENTER. The LCD panel will display Tech Mode. 3. Press the left arrow (<) button once. The operator panel will display NEW CARTRIDGE. 4. Press ENTER. The operator panel will display [YES]. 5. Press ENTER. The toner warning message should be gone. 6. To exit TECH MODE, press MENU # 1 9 3 4 in rapid succession, as if you were dialing a phone number. The operator panel should no longer display TECH.
If problem persists, there may actually be a problem with either the toner cartridge or the SCX-4216F.
Works for SCX-4521F
Re: how to reset samsung scx 4521f by mahfuz (9/18/07 7:56 AM) reply
Whoa -- that works great. Thanks. I was about to go screaming back to Fry's about selling me an empty cartridge. Of course, it wouldn't have been the first time I took something back to them as "broken" and later discovered that I'd just screwed up in installing it.
Re: how to reset samsung scx 4521f by mrhenry (4/6/08 7:42 AM) reply
Anonymous -- your fix works great!!!! Remember all the enter the # sign first. Internet is wonderful for fixing problems. I simply search on "scx-4521f toner low message remains on", and found your fix in seconds
Re: Re: how to reset samsung scx 4521f by Anonymous (5/16/08 1:13 AM) reply
I've tried to end a fax but there was no answer, so my printer tried dialling all the time.The problem is that i have tried cancelling the job with no response, i've tried to make copies but the printer gives me this message : dial fax number then press start, this is when i'm try to make copies. How do I reboot my printer?
Re: how to reset samsung scx 4521f by Anonymous (5/16/08 7:59 AM) reply
When I try to fax multiple pages the machine gets stuck on "sending page 2" or "sending page 3" and doesn't complete the fax. Every now and then it works like it should and it always works if I'm just sending one page. Help please!
Re: how to reset samsung scx 4521f by Anonymous (7/3/08 12:36 AM) reply
Does anyone know how to reset a Samsung SCX 4828FN? Using the instructions of Anonymous above on the 4828 does not work. IN fact, using the instructions above does get you into Tech mode, but pressing the back key does not provide the option of new cartridge.
By the way, I am using the starter cartridge. I have filled the toner and the printer is still printing despite showin toner empty. I am far from being an expert on this, but it could keep working this way. However, the flashing red light showing toner low/empty is annoying.
Any advice anyone has on how to get rid of this toner low message would be appreciated. You can contact me directly at riccardo2008_ca@yahoo.ca.
Thank you!
Ric
Re: how to reset xerox pe220 by sajith (5/24/09 8:58 PM) reply
Instructions for inserting a toner cartridge in the printer SAMSUNG SCX-4521F when this has been refilled or if a cartridge is not original.
The Samsung SCX-4521F printer only recognizes the original cartridges SAMSUNG and rejects those who despite being originals have been refilled
When this happens, on the screen printer appears the mesage "TONER EMPTY" and every time you turn the printer on you will hear an annoying beep.
To prevent this from happening, when you replace a cartridge that is not genuine or has been refilled, you must enter the unlock code and follow the steps listed below:
"Unlock Code"
1. Press the "MENU" option followed by "#" and enter the code "1934". 2. The screen should display the word "READY" 3. Move with the arrows until you find the option "NEW CARTDRIGE" 4. Choose "YES" by pressing "OK" 5. Press again the key "OK" 6. Turn the printer off to restart the machine.
Re: how to reset samsung scx 4521f by Anonymous (9/26/09 1:17 AM) reply
I have a SCX-4826fn. I can't find a fuse on the toner cartridge. I bought a refurbished cartridge out of sheer necessity and noticed that this cartridge had four contact plates on the front top side of it. Whereas, the original cartridge that came with the printer had nothing.
Thanks!
Re: Re: how to reset samsung scx 4521f by Anonymous (10/14/09 10:04 AM) reply
I tried it again, but it still doesn't work. I have a Samsung SCX-4826fn. When I press #1934 it gets me to tech mode but it doesn't give me the option of a new cartridge. Any one having any success out there?
Gord
Re: how to reset samsung scx 4521f and toner low by color (11/20/09 1:28 AM) reply
i have SCX-4521F AFTER REFIILING OF ORIGINAL TONER CARTRIDGE IT SHOWS LOW TONER MSG ON DISPLAY . HENCE REQUEST YOU TO SUGGEST THE WAYS TO GET RID OF THIS PROBLEM .
Re: how to reset samsung scx 4521f by Pavel from ukraine (11/20/09 4:57 AM) reply
say "thanks" to mr. Alutov! Because he has made new fw for samsung 4824. People, go to startcopy.ru and find in "konferencia". but you must learn russian language.
I have replaced my samsung scx 4521 printer cartridge with a remanufactured/refilled toner. I got the error message cru fuse error. Samsung agents charged me R750 for replacing the liu board, etc, but still the printer tells me CRU fuse error. The samsung guys insist the toner is faulty and I need to buy a new one. Please can anyone advise what to do.
Re: how to reset samsung scx 4521f by Lsc David (12/22/09 6:48 AM) reply
press menu 8 times in reports press > button whenever you get system data press enter a system data page is printed there on this page you can find how many pages was printed with current cartridge it called total page counter
Re: how to reset samsung scx 4521f by Anonymous (1/21/10 9:10 AM) reply
Post to this thread Post a new message thread
