fixyourownprinter.com
  Home    Reference    Forums  
  Printer Repair | Laser | InkJet | Chat | SearchSign In | Sign Up  

Oki c5300n drum reset??

Post to this thread   Post a new message thread

Oki c5300n drum reset?? by Trent (9/28/04 4:17 PM) reply+3 + / -
Is there a way to reset the drum counter on an Oki c5300n. Rather than purchase individual new drums, I bought a c5100n printer to use for parts since all parts except the processor are interchangable. I found out later that the drums, fuser, and belt transfer have a built-in fuse for counter resets that is blown at the factory during testing. Oki Tech Support says the only way to reset is to buy a new Oki part that has never been in a printer.


Re: Oki c5300n drum reset?? by rich (10/3/04 4:57 PM) reply + / -
I have a 9500 and the same problem, all 3 color cartridges go out at once. On average you can get a extra half life out of them and even more if you take them apart and recoat the roller. I heard of on person who refers to some part that could be replaced, but I would prefer a menu reset option. The key is to be able to reset that drum counter.



Re: Oki c5300n drum reset?? by moe (1/29/05 5:06 PM) reply + / -
Try this procedure, don't know if it will work on your models.

Turn off the printer
Turn the printer on whilst holding down Menu button. (Display says user maintenance.)
Press the menu button three times. (The display will say drum counter reset.)
Press enter key. The system should go back on line, if not press on-line key.


Re: Oki c5300n drum reset?? by moe (1/29/05 5:09 PM) reply + / -
Also found this Oki service manual that has a similar procedure on page 20.

http://www.precision.com


Re: Oki c5300n drum reset?? by bazzag (8/8/05 5:34 AM) reply + / -
Hi
You can just put a new fuse on the drum.
When you insert the drum the machine resets the counter and then blows the fuse. So if the unit is ok and you just wish to run it through another cycle just change the fuse.
This means you cannot just put a full unit in from another machine as it will not reset the counter until you put a new fuse in it as you found out.
This applies to drums transfer belt etc.
Note with regard to refilling the toner, some printers have 2 sections. 1 where you put the fresh toner and an after collection section in the same unit. You must empty the 2nd section if you refill it more than 2 or 3 times


Re: Oki c5300n drum reset?? by Anonymous (8/10/05 3:04 PM) reply + / -
you open the drum unit on top and look on the side cover

the green fuse is there



you juste replace it by clipping it in


that all


Re: Oki c5300n drum reset?? by Anonymous (8/11/05 9:10 PM) reply + / -
Reset the Drum Counter:
a. Press the MENU 1/Menu 2 button while turning the
printer on.
USER MNT appears on the display.
b. Press the MENU 1/Menu 2 button until the message
corresponding to the drum you are replacing
appears. For example, if you are replacing the
magenta image drum:
MAGENTA DRMCNT
RESET
c. Press the ENTER/POWER SAVE button.
RESETTING briefly appears on the display.
d. Press the ON LINE button.


Re: Okidata c5150n toner reset?? by Rick Lee (8/30/05 2:22 PM) reply + / -
The original toner cartgidge cannot be refilled. I did not know this when I refilled it. The cartridge worked great for another 100 pages until the internal counter said it was empty. The cartridge is full but it needs to be reset somehow. This is the original cartridge and there is not a flag on the end like the replacement cartridge. Does anybody know how I can use this again? Thanks


Re: Re: Oki c5300n drum reset?? by Anonymous (9/10/05 3:24 AM) reply + / -
I need Reset Fuse for OKI C5100 for all Drums and any others I may need later. Appreciate your advice and cost how I can buy these. I am in the UK.

Best regards

Dave


Re: Oki c5300n drum reset?? by burgi (edited 9/15/05 12:34 PM) reply + / -
Artikelnummer bei RS Components GmbH

httt://www.rsonline.de


422-012 Fuse flink 1/8 A = 125 mA -- 10 Stück 4,75 + MwSt.


einfach auslöten-einlöten

you open the drum unit on top and look on the >left< side cover

the green fuse is there <-- sieht aus wie ein Metallfilmwiderstand



Re: Re: Oki c5300n drum reset?? by Anonymous (9/24/05 9:09 AM) reply + / -
I could have information for resettare drum oki 5100 or and oki 9300


Re: Re: Oki c5300n drum reset?? by Anonymous (10/21/05 5:51 AM) reply + / -
I have an OKI 7200 colour led printer. Could you tell me how to reset the drum counters?

Thank you.


Re: Oki c5300n drum reset?? by Anonymous (10/26/05 9:25 AM) reply + / -
Reset the toner by holding it vertically (as it would sit in the printer). Rotate the wheel opposite the blue lockin until the white "indicator" disappears in the window (about 1 full turn). Power cycle the printer, this should reset.


Re: Re: Oki c5300n drum reset?? by Anonymous (10/26/05 9:33 AM) reply + / -
Please email reset fuse order information.
Thanks
AL


Re: Oki c5300n drum reset?? by RTINSC (11/2/05 6:09 PM) reply + / -
Okidata 51-5400 series drums will lock around 16000 pages. When you hear "clicking", drum is locked. Buy fuses on ebay for 7.00 and install before drum locks.

Undo two small screws on top of drum unit (remove toner cartidge) and carefully pry off the cover. Set drum on its legs so you don't spill toner. There is a hidden hook on lower left of cover- pry open at slot just below serial number tag. Install fuse where you see two copper or brass connectors. (Starter drums do not have a fuse installed). Reassemble.

Refilling toner. Buy toner on ebay (40.00). To refill, remove toner cartridge and turn upside down. Turn the blue knob so the bottom slot opens. There is a little peg near blue knob that when pushed in, allows the blue knob to turn so the toner slot opens. Fill the cartridge with new toner and close the blue knob. The cartridge is only a tank and can be used many times. Two thirds of the cartridge from the blue knob side is the tank. The third to the left is the waste tank. The waste tank needs to be emptied after about two refills. Take a sharp knife and heat it to cut a hole in the top of the cartridge (2 inches or so from the end opposite the blue knob.)Use a vacuum or turn cartidge upside down and empty. Tape up the hole. You can also cut a hole in top 2 inches from blue knob to load toner.Tape with duct tape.

I do a lot of printing and can get about 8000 prints per reload. You will use less CYM toner than black. About 25000 prints on drums.

If you start up printer and simultaneously holding the two menu buttons (up/down) you will get a new set of menu options. There is no drum reset item. If anyone has info about the other menu items, please let us know.


Re: Re: Oki c5300n drum reset?? by Anonymous (12/22/05 7:49 AM) reply + / -
I need the reset fuse to reset fuser and transfer belt in the Oki C5100, do you have ?


Re: Oki c5300n drum reset?? by Anonymous (12/31/05 5:22 PM) reply + / -

This page has the most terrible community spirit for any forum I have come across. Everyone is hiding their knowledge or assumes other readers are engineers.

For the sake of having such a forum and community spirit!!!

Can someone provide a pictorial instruction on locating and reseting the fuse.


Re: Oki c5300n drum reset?? by Anonymous (1/31/06 11:45 PM) reply + / -
I think I found a way to reset all consumables (drums, transfer belt, & fuser; excluding toner cartridges) using only the menu. Thus, NO FUSES will be required--sorry all you eBay entrepreneurs, you rode this one out long enough! I was experimenting today (bound and determined to minimize my costs), and the following worked to reset all four drums on my C5300n. Hopefully, the steps work for other models as well. So, here goes:

1) Power on printer while holding both the + & - buttons simultaneously; release when “OKIUSER” is displayed.
2) Press either the + or – button until “ENGINE DIAG MODE” is displayed; press the Enter button and “DIAGNOSTIC MODE xx.xx.xx” will be displayed.
3) Press and hold both the - & On-line buttons simultaneously until “ENG DIAG LEVEL2” is displayed.
4) Press either the + or – button until “CONSUMABLE COUNTER SET” is displayed, press the Enter button; you are now in the menu to set various consumables.
5) Press either the + or – buttons to scroll through the various consumables, at the desired consumable (ie. “K-ID UNIT …” for the Black Image Drum Unit) press the Enter button and the last digit of the count will start flashing.
6) Press the Cancel button to decrease the digit amount or press the On-line button to increase the digit amount; press the + or – buttons to move along individual digits in the count.
7) Once the count is at the level you desire (I reset mine to 50), press and hold the On-line, Cancel, & Back buttons (yes, it’s 3 of them this time) simultaneously until the “*” reappears next to the count; you have reset that consumable’s count to the number you specified.
8) Press the + or – buttons to move to the next consumable and repeat at step 5.
9) Once all consumable counts have been set to desired amounts that are below their end-of-life thresholds, you can use the Back, +, & - buttons to exit through the menus (reverse of steps 2 through 4) until “INITIALIZING” is displayed.
10) You're finished! Now log in to the web interface with your browser and check to see the remaining life of your consumables.

Good luck!

-Glenn


Re: Oki c5300n drum reset?? by Anonymous (2/1/06 10:39 PM) reply + / -
Were you able to call up any other Engine Diagnostic Levels? I came about my solution to the C5300n by adapting Oki's own knowledge base article where they gave instructions to correct a printer (C5100 & C5300n) being in Factory Mode as opposed to Shipping Mode. In those instructions, they specified a key combo to get to "ENG DIAG LEVEL3"--that being holding both the Enter & On-line buttons simultaneously until such appears on the display. I had read somewhere on the web that Level 2 was the menu I needed, so I simply started trying various key combinations and alas, the one I provided worked. From there, the hardest part was determining the correct key combination to apply (save) the new count.

There has to be a key combination that will work with the 5400! Keep trying, the menu has to be hidden somewhere within. Believe me, a couple of hours spent on this is well worth the $400 or so Oki would like you to spend on new drums.

Also, make sure you get “DIAGNOSTIC MODE xx.xx.xx” displayed in step 2 by pressing Enter at "ENGINE DIAG MODE". From there (and only there) was I able to press and hold the particular key combos to get into the individual diagnostic menu levels.

Sorry for the lengthy post. Keep us all updated.

-Glenn


Re: Oki c5300n drum reset?? by Mr.Kim (2/10/06 10:22 AM) reply + / -
I tried Glenn's ten step approach for my OKI C5150n. It didn't work. I did find another post on this site that did work for me. It reset all drums, toner and fuser to 99%. That thread was posted by RTINSC and this should link to it. http://www.fixyourownprinter.com/forums/laser/33634#1 This after dissasembling my drum (messy) and lots of internet research. No fuses, could have avoided the toner mess. Thanks for that post. Mr.Kim


Oki c9300n drum reset?? by Anonymous (2/17/06 1:08 PM) reply+1 + / -
Try this. i´ve a c9300n...

1 - Power ON printer while holding both the + & - buttons until “OKIUSER” message apear in LCD.
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again... =)

To access Service Mode in C9300 power ON printer with 0, 1, 6, 7 at same time...



Re: Oki c9300n drum reset?? by Anonymous (2/17/06 2:05 PM) reply + / -

Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, and on and on.

For the C5400n, executing reset under table 1 works. All ID counts / Toner Life / Fuser Life & Belt Life rest to 100%.

If i could buy you a virtual beer i would give you several. Cheers!!!!

Can you explain what buttons correlate to 0, 1, 6 & 7 though.

Rapper.




Re: Re: Oki c9300n drum reset?? by Anonymous (2/20/06 3:06 PM) reply + / -
it seems like this:

(menu) (+) (+) (select)
0 1 2 3

4 5 6 7
(on-line) (-) (-) (cancel)

press at same time these FOUR buttons...

executing reset under table 1.... reset all consumables to 100%

now i´m studing, how to reset individually C,M,Y,K toner and DRUM... it´s possible, but i don´t know how yet.. =(

i also have a C5200n, reset under table 1... reset all too... =)




Re: Oki c7200n drum reset?? by Anonymous (3/1/06 1:33 PM) reply + / -
1 - Power ON printer while holding both the + & - buttons until “OKIUSER” message apear in LCD.
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Hold "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again... =)


Xerox 7300 Imaging unit reset?? by dafry (edited 3/26/06 11:59 PM) reply + / -
I have a xerox 7300, which uses the same drum kit us Oki 9300 but xerox call it "imaging unit" any ideas for reset???
Thanks


Worked for a c7350 by melpheos (4/11/06 5:39 AM) reply + / -
Hi everyone,

we have a 7350 and the buttons 0167 worked for displaying the hidden maintenance menu.

the internal structure of the menu is a bit different from the 9300 but i managed to find the right place where the nv-ram inital menu is located

Thanks a lot for the help


ReOki 9800 consumables reset code by Anonymous (4/12/06 9:17 AM) reply+3 + / -
Hi,
We have Xante CL30 HSE, which really a OKI 9500 that has been converted to take heavy stock and we have the reset procedure for the fuser, belt and drums, etc.
The drums still have about 8000 extra clicks in them when the printer tells you game over.

We recently bought an Xante Ilumina, which is really and OKI 9800 converted, but I dont have the procedure to reset the drums - can you possibly help?

Best wishes,
Bruce Gatland


Re: Re: Oki c5300n drum reset?? by Anonymous (4/21/06 9:17 AM) reply + / -
Thank you Mr. Kim I used your link & it worked perfectly on my c5150n. Thank you!


Re: Oki c9300n drum reset?? by Anonymous (5/3/06 6:44 PM) reply+1 + / -
THANK YOU!!!!!!!! I was able to reset my C3200n. I refilled the starter cartridges and now everything works. Thank you! Thank you!


Re: Re: Oki c5300n drum reset?? by Anonymous (5/16/06 8:52 AM) reply + / -
Thanks a bunch. Your procedure works like a charm on my C5100N.


Re: Re: Oki c5300n drum reset?? by matrix9199 (5/28/06 9:23 AM) reply + / -
Glenn, Thank you a lot!!! It works perfectly on the c5100n too... I modify the FUSER and the TRANSFER BELT life too. Do you think I will have problems in the future?
Regards.

Matrix9199


Re: ReOki 9800 consumables reset code by Anonymous (5/31/06 8:04 AM) reply+2 + / -
I HAVE A XANTE CL30 PRINTER.
IS THERE A WAY TO RESET THE DRUM,TONER,FUSER,etc back to 100% ????

thank you advance

STAVROS ZACHAROPOULOS


Re: Worked for a c7350 by Anonymous (6/6/06 6:58 AM) reply + / -
success:

Found the "ENG DIAG LEVEL4", which allows a hell lot of things:
* Individual counters set
* enable/disable checks
* more dirty stuff

1) - Power ON printer while holding both the 0, 1, 6, 7 buttons (see above posts) until "OkiUser" appears
2) go in the menu to "DIAGNOSTIC MODE XX.XX.XX Shipping"
3) Press 3 and 2 button until “ENG DIAG LEVEL4” is displayed;

4) now you have the options up/down with buttons 2 and 6, escape with button 4 and "change value" buttons with 3 and 7

5) changing values means blinking numbers

What remains and needed is, how to "save" these options. Well you've got to figure that out. I would guess a 3-button-combination...

cheers


Re: Re: Oki c5300n drum reset?? by Anonymous (6/7/06 2:16 PM) reply + / -
Glenn - You da man!!!

Your 10-step method worked beautifully on my c5100.

I owe you lunch next time you're in Tulsa!!

Tom


Re: ReOki 9800 consumables reset code by john6664 (6/7/06 2:59 PM) reply + / -
any luck with the reset codes, I now have a ilumina and the consumables are killing me....


John


Re: Oki c5300n drum reset?? by Anonymous (6/15/06 3:37 AM) reply + / -
Glenn:

Your instructions sorted out an Oki C5100 as well. Many thanks!


Re: Oki c5300n drum reset?? by bLiTzJoN (6/17/06 7:56 AM) reply + / -
Found this on CNET/NY Times. I'm assuming it's a factory reset for everything.

Full user opinion
This printer tries to force you to buy expensive replacement toner cartridges and image drums well before their useful life is over (automatically shuts down after preset number of pages). To work around these limitations, you can do the following:

1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

All toner, drum, fuser and transfer figures return to 100%. Of course, if you are out of toner, you do need to refill the cartridges, but you can find refill toner and instructions on ebay (a bit messy, but cheaper than new cartridges). The drums, etc. won't work forever, but they will work longer than the artificial limits imposed by Okidata.

Here's the source http://tinyurl.com/lh36z


Re: Re: ReOki 9800 consumables reset code by Alepou (6/20/06 2:36 AM) reply + / -
Dear Stavros Zacharopoulos if you are leaving in GREECE
Call 28210 92246 (Hania-Kriti) or give me your e-mail
for free Instructions to resetttttt your printer
they are little difficult to write but it is possible.
Thank you
Nik


OKI C5400 Drum reset/ OKI 5400C toner cartridge / by Anonymous (7/17/06 10:38 AM) reply + / -
Glenn,

The 10 step instructions for re-setting the drum/belt/toner cartridges you suggested for the worked perfectly except for turning the printer on - I unplugged and re-plugged the unit for those steps for my C5400. Thanks a lot!!!

Your steps again...1) Power on printer while holding both the + & - buttons simultaneously; release when “OKIUSER” is displayed.
2) Press either the + or – button until “ENGINE DIAG MODE” is displayed; press the Enter button and “DIAGNOSTIC MODE xx.xx.xx” will be displayed.
3) Press and hold both the - & On-line buttons simultaneously until “ENG DIAG LEVEL2” is displayed.
4) Press either the + or – button until “CONSUMABLE COUNTER SET” is displayed, press the Enter button; you are now in the menu to set various consumables.
5) Press either the + or – buttons to scroll through the various consumables, at the desired consumable (ie. “K-ID UNIT …” for the Black Image Drum Unit) press the Enter button and the last digit of the count will start flashing.
6) Press the Cancel button to decrease the digit amount or press the On-line button to increase the digit amount; press the + or – buttons to move along individual digits in the count.
7) Once the count is at the level you desire (I reset mine to 50), press and hold the On-line, Cancel, & Back buttons (yes, it’s 3 of them this time) simultaneously until the “*” reappears next to the count; you have reset that consumable’s count to the number you specified.
8) Press the + or – buttons to move to the next consumable and repeat at step 5.
9) Once all consumable counts have been set to desired amounts that are below their end-of-life thresholds, you can use the Back, +, & - buttons to exit through the menus (reverse of steps 2 through 4) until “INITIALIZING” is displayed.
10) You're finished! Now log in to the web interface with your browser and check to see the remaining life of your consumables.

Good luck!







Re: Re: Re: ReOki 9800 consumables reset code by Anonymous (7/18/06 1:22 PM) reply + / -
Dear Sir ,
Can you help-me with steps to reset couter for one oki 9800
printer

Tank's

Marcos


Re: Re: Oki c5300n drum reset?? by Anonymous (7/21/06 9:12 AM) reply + / -
Glenn you are a star. Fantastic. Your procedure worked on my C5100n.

Thanks
Roger


Re: Re: Re: ReOki 9800 consumables reset code by suzykoala (7/25/06 10:50 PM) reply + / -
Hi Nik, I was wondering if you have the oki 9800 consumable reset code. my email is susan@koala.net I would be greatly appreciated if you could give me the code. Thank-you very much


Re: Re: Oki c5300n drum reset?? by Dave_19 (7/29/06 5:01 PM) reply + / -
Hey Glen!
Brilliant results on mt C5100. Everything works just as you said!
Thanks for saving me hundreds of dollars.
Cheers Dave


Re: ReOki 9800 consumables reset code by luka (8/3/06 8:05 PM) reply + / -
I have a Xante CL30 and am interested in the consumables reset code, can you help?


oki c5500 reset question. by pointblizzy (8/15/06 1:34 PM) reply+2 + / -
Does anyone have any Idea on how to reset the C5500 drum? I know it's kinda new but, it seems like I am the only one with this printer.


Re: Oki c9300n drum reset?? by Anonymous (8/26/06 1:04 PM) reply + / -
Hi, can anyone help ? I have a C9500 dxn Oki, ..... in need of a drum(s) reset....
I've tried instructions on the c9300.....+ and - buttons but it will not come up OKIUSER --- I Can't get to the ENGINE DIAG MODE ??? HELP PLEASE PLEASE PLEASE.....


Re: ReOki 9800 consumables reset code by john6664 (9/19/06 8:30 PM) reply + / -
I also have a Xante Ilumina and am in great need of the reset codes, could you pass along anything you have found...

john@logoprinting.com


Re: Re: Oki c5300n drum reset?? by Anonymous (9/29/06 6:56 AM) reply + / -

Thanks Glenn you are a brick. Great instructions. Perfect result no more money on fuses.


Re: Oki c9300n drum reset?? by Anonymous (10/4/06 6:56 AM) reply+1 + / -
Well done sir!!!!!!! Works a peach. Now can anyone tell me how to do it on a 3300 (no LCD panel)??


Oki c5400n Toner Count disable. by Caelum (10/4/06 5:50 PM) reply + / -
Drum resets i've worked out, from some of the posts above, by resetting the Table 1 NV-RAM page.

however, i've noticed a problem with it and toner count resets... initially it worked fine, resetting the usage for each toner to 0%, however it seems that after a while, this has stopped working, resetting only some of the toner counts, and putting the others at 95-100%.

i've since found a way to turn off the toner counter all together, so that there is no warnings for 'low toner' and it wont stop and tell you to replace the toner when it is empty, however this also allows us to completely use the toner untill empty.

How to turn off toner page counting on the OKI C5400n


1) Turn off printer.
2) Turn on printer, while holding the + and - buttons.
3) The LCD Shows 'OKI User', Scroll to "Engine Diag Mode", hit enter. The display shows "Diag Mode 01.02.02 S-Mode"
4) Scroll to Eng Param Set 2, Hit Enter.
5) Scroll to Toner Sensor(it may be the first one), hit enter, Change setting to "Disable"
6) To set the "Disable" setting you need to press the ONLINE, CANCEL and - Buttons at the same time, pressing ONLINE first.
7) Press the Back Button.
8) Turn off the Printer, Leave for 10 seconds, and Turn back on, as normal.



No more toner warnings... :)



Incidentally, as far as drum life goes, i've found close to a 100% increase by resetting Table 1 in the NV-RAM... certainly saves me a lot of money, considering we used to go through atleast 1, if not 2-3 a month.


Thanks for everyone's helpful posts, i hope mine comes in useful for others too :)


Re: Oki c5300n drum reset?? by jeff_jordan (10/17/06 11:15 AM) reply + / -
@Glenn:
a big THANK YOU from my site.
It worked perfect with the C5100n that I managed to buy thru eBay.
Now I'm going to refill the toner cartridges and will be happy with my bargain ;-).

Again: thank's a lot, you're the man !


OKI C7200dn maintenance menus by Caelum (10/17/06 6:10 PM) reply + / -
Wow... Just wow.....

I dont have all the menus here.. but from what i've worked out, i'm sure that you can all figure what to do in certain other menus...

ok.. here goes :D


C7200 maintenance Menu's


1) Turn on Printer while holding the 1 & 2 buttons.

2) Using button #1 scroll down untill you see "Diagnostic Mode 00.22.00", then hold down buttons 2 & 3.

3) You now have "Engine Diag Mode Level 4" showing on the display.

4) Use Buttons 1 & 5 to scroll between menu's. Scroll down to "Counter Set".

5) Use Buttons 2 & 6 to scroll between menu items. Use buttons 3 & 7 to change the value you wish to alter.

6) The Flashing number is the value you have highlighted. Use Buttons 2 & 6 to change that value.

7) When you have made any changes you need to, hold down buttons 1, 3, and 5. The screen will flash 3 times, then an * will appear at the end of the screen. The Value has been set.

8) The "ID" unit appears to be the drums, setting these values changes the drum usage according to the printer.
The Toner counts are in percentages, and can be changed from 000% to 999%, where 0% is no use, and 100% is totally used.
The "Dot Count"s set how many times each colour has been used, in the life of that toner(?).
The "Total Dot Count" is the same as the above, but for the entire life of the printer.
The "Replace" values for belt, fuser, drums, and toners show how many times each of those units have been replaced.
The Printer life limit seems like an odd one... its there to make you replace the printer after x(600000) number of prints?
There are also life limits for toners, drums, fuser units, belts etc, which can be changed from the default values.
The (cmyk) "ID Unit" shows how many pages have been printed that include that colour since that item has been installed.
The (cnyk) toner percentages can be changed here manually, but is no use if you've turned off toner counting in the below step.

9) To turn off Toner counting:

After getting into Eng Diag level 4, scroll down to "Engine Parameter Set 2".

Use the 2 & 6 buttons to scroll between options. Scroll to "Toner Sensor".

By Default, this is "Enable".

Change the values by using the 3 & 7 buttons. When you've changed the value to "Disable" press both the 3 & 7 buttons together, and the * will appear, showing that you've set the value correctly.

You can also apply the above change to the "ID Unit"s aswell, being the image drums, to stop any counting of the drum units, allowing them to be used untill image quality suffers.

The above change can also be made to the "Belt Unit" and i'm guessing Fuser unit aswell.








Hope this helps a few of you :)


C3200n Consumable Counter Set by Nono (10/19/06 12:46 PM) reply + / -
A C3200N here...

I never wanted to do the NVRAM complete reset because I was scared of losing the network MAC address as mention somewhere else on this forum. And basically controlling the consumable level independently was interesting… My c3200n printer was bought last month (09/2006), guessing here that the bios may be different depending on release date (this walkthrough might not work for everyone).

Sooooo, after much button pressing, restarts and coffees.. here it is:

Get to the standard "Diagnostic mode" as describe on this thread:

1) Turn off printer.

2) Turn on printer, while holding the + and - buttons.

3) The LCD Shows "OKI User", Scroll to "Engine Diag Mode", press "enter".

The display shows "Diag Mode 01.02.02 S-Mode" as mention multiple times on this thread.

At this point you should wait for the initialization cycle to complete. I mean for all the motors and gears to have finished their noises and cycles – otherwise you will end up with a LCD switching between two different info screens - not a big deal but still annoying.

Now we want to go in "regist mode" by:

1) Pressing the "Online", "Cancel", "Enter", "-" and "Back" AT THE SAME TIME (not in any sequence – at the same time). Yes! That is 5 buttons.

2) After within two seconds the LCD menu will show "READY". If it doesn’t, release button and repress buttons again.

3) The buttons release sequence is important. So, read this before letting go your five fingers: Release the "Enter" button first and THEN the four others. LCD is still showing "READY".

4) Press the "Online" and "Cancel" button at the same time BRIEFLY. Don’t wait before pressing them after the five fingers sequence otherwise you will miss your time slot.

You can always switch back from the "READY" to the "Diag Mode 01.02.02 S-Mode" menu by pressing the five buttons again.

Don’t laugh. I know it seems a lot of gymnastic. Well I guess they didn’t want the user to find that one easily.

Now you see "Eng Diag Level 2"

Taking from someone else on this thread (with some modifications for the c3200n):

Press either the + or – button until "CONSUMABLE COUNTER SET" is displayed, press the Enter button; you are now in the menu to set various consumables.

1) Press either the + or – buttons to scroll through the various consumables, at the desired consumable (ie. "K-ID UNIT …" for the Black Image Drum Unit, "C-Toner" for cyan toner, etc.), press the Enter button and the last digit of the count will start flashing.

2) Press the Cancel button to decrease the digit amount or press the On-line button to increase the digit amount; press the + or – buttons to move along individual digits in the count. Note that it will not show the remaining but the usage (100% means it is empty).

7) Once the count is at the level you desire, press and hold the On-line, Cancel simultaneously until the numbers stop flashing; you have reset that consumable’s count to the number you specified. Note that you may end up with a different value then the one that was entered when saving. The printer engine is probably jumping to the nearest registered/acceptable value. If someone find a way to save the exact value, let us know.

8) Press the + or – buttons to move to the next consumable and repeat at step 5.

9) Once all consumable counts have been set to desired amounts that are below their end-of-life thresholds, you can use the Back, +, & - buttons to exit through the menus (reverse of steps 2 through 4) until "INITIALIZING" is displayed. Or turn printer off and on.

10) You're finished! Now log in to the web interface with your browser and check to see the remaining life of your consumables.

There is another way to get to the "Eng Diag Level 2" menu – I did it at one point but wasn’t able to reproduce. But this method worked for me even if you may need some practice. You can also get to level 3 and level 4 after the release of the five fingers step by pressing something else then the "online" and "cancel".

Good luck.
Nono






Re: Oki c5300n drum reset?? by Anonymous (10/20/06 11:17 AM) reply + / -
Nice work Nono and others. This is great stuff...especially when you know the manuf. is working you for every penny. I love the c3200n printer quality etc. but was very fed up with the shutdowns for "Factory Empty" settings versus using every last drop.

Much appreciated. But, I do recommend this printer it puts out very nice copy.

ScottZilla


Re: Re: Oki c5300n drum reset?? by Anonymous (10/25/06 9:42 PM) reply+1 + / -
Thanks for the HOW TO
Your instructions were great - It worked perfectly
It will be interesting to see how much longer the drum will work since it has 14,530 on it.


c5400n ....... how to do it for specific firmware by Anonymous (11/29/06 9:17 AM) reply + / -
hi guys

thanks to nono for the info above

i've used this sequence successfully to reset the drum count on a C5400

just follow the instruction as per nono post above
C3200n Consumable Counter Set by Nono (10/19/06 12:46 PM)

one thing i think is happening is that different firmware revisions are changing the key sequences, hence some of them working sometimes and not others

i'm running 1.03.03 and the above worked .......

so take note of the "Diag mode nn.nn.nn S-mode" as i think it is more significant than the model in some instances






Re: ReOki 9800 consumables reset code by A C Biggs (edited 12/14/06 8:09 AM) reply + / -
Can you help with the reset codes for the Xante CL30HSE? I didn't know such things existed! Our black drum is complaining! Have you managed to source cheaper toner cartridges? I have been trying the toner refill option but with dire consequences - background tinting, streaks etc. I think the make up the Xante toner is different to that of the Oki machines perhaps to take the extra heat of the fuser


Re: Oki c5300n drum reset?? by theele (1/9/07 5:10 AM) reply + / -
oki c5300n:
does anybody knows how to reset (or set) following counters
(these are not drum counters!):

Usage Menu / Color page count
Usage Menu / Mono page count

it seems both show total number of pages printed from printer "first-time". Anyway to reset them or only physically change eeprom?


Re: ReOki 9800 consumables reset code by Anonymous (1/23/07 2:27 PM) reply + / -
Hi Bruce
Long story - but I also have the Xante CL30 - would you share those codes with me please
I am getting a Fatal Error 127 - any idea what that is?
Thanks
Paul


Xante cl30 hse by Bloke (1/24/07 5:33 PM) reply+1 + / -
Warning,

The xante cl30 hse is indeed a an oki c9500 engine but xante have put their own circuit board in. On that basis, using oki reset codes could lock you out of the machine entirely !

Secondly, a BIG VOTE of no confidence for xante as this machine is the worst performing machine I have ever encountered in my entire life. The xante drivers and firmware are shockingly poor beyond imagination and the print quality is virtually uncontrollable.

Run a job on heavy stock followed by a job on thin stock and the machine will destroy everything you print for several hours, regardless of correct colour / media settings.

This so called "heavy stock convertion" is simply a new board and drivers that slow the machine down and increase the heat of the fuser. Thats all and the rest of this machine is standard oki stock and will wear out a lot faster than the oki 9500.

I have spoken to Oki and they "unofficially" told me that Xante are pushing the engines way beyond their design limits. Lets face it, if the engines were designed to handle 330 gsm or even higher on the illumina - then Oki would be advertising heavy stock themselves !

Yes folks, I am a very unhappy Xante customer.




Re: OKI C7200dn maintenance menus by mikey14 (2/4/07 2:43 AM) reply + / -
Thankyou so much for the detailed reset. it workd fine on an OKI C7350 exactly as you described


Re: Oki c5300n drum reset?? by Blonde Guy (2/12/07 2:28 PM) reply + / -
I've got an Oki c5300, and Glenn's procedure worked for me. Many thanks for a great website.


Oki c5450 and c9300 Drum, Toner, Fuser, Belt Reset by gix (2/24/07 12:32 AM) reply+1 + / -

Drum, Toner, Fuser, Belt Reset on:

OKI C9300n

1) Power ON printer while holding both the 0, 1, 6, 7 buttons until “OKIUSER” message apear in LCD.
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again... =)

OKI C5450n

1) Power ON printer while holding both the + & - buttons until “OKIUSER” message apear in LCD.
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again... =)


Re: Re: Re: ReOki 9800 consumables reset code by youngs (3/7/07 4:56 AM) reply + / -
Nik

Any chance of the Oki 9800 reset codes? I see quite a few others are desperate too so it would be great to see them on the forum.

Martin
martin@saysales.com


Re: Re: Okidata c5150n toner reset?? by Anonymous (4/4/07 11:10 PM) reply + / -
Do not forget to remove the waste toner or you may ruin the drum section.


Re: C3200n Consumable Counter Set by Anonymous (4/5/07 9:26 AM) reply + / -
Works fine on my two C5200N printers with one modification:-
Entry to "regist mode" ... when all five buttons depressed, release "On Line" first followed by remaining four. Works every time when you get used to quick response required after the four buttons are released. I use one C5200N with only OKI consumables. On other I use compatible toners - some are not and destroy the drum very quickly (personal experience). Others are very good and produce similar results to originals.


Re: Xante cl30 hse by Anonymous (4/5/07 11:24 AM) reply + / -
Totaly agree!! We paid nearly £400 for training and installation, it turned up 2 days early and was left in the car park on a pallet, it took four of us to lift it in. The so called 'training' took all day and was a farce. We have had ours a year and have now replaced it because of its unreliablility and high running costs. The figures quoted to us at the time of sale are way out. We travelled to Poole and had a row with the sole importers of this machine about its quality etc, and they certainly showed their true colours!! The machines are imported from The Netherlands and re-badged. I put it to the company that they were the equivalent of a 'Pimp my Ride' firm, suping up the fuser unit, probably adding spacers to the drum units so 330gsm board will go through. We have now installed a Konica Minolta C300 Bizhub - AMAZING!! All installed in an hour and setup within 10minutes. We pay a click charge of 6p per A3 side with as much coverage as you want and 0.006p per black and white!! It has a docu-feeder, A3 scanner you can scan to fax, e-mail, or JPeg or convert documents to PDF in the blink of an eye!! The click charge includes all toners, drums, transfer belt and servicing - (Plus the lease charge of course cost of machine just slightly more than the Xante) The Xante is way out of its depth and should be avoided at all costs that also goes for the Illumina - another re-badged Oki.


Re: Re: Oki c5300n drum reset?? by Anonymous (4/11/07 11:44 PM) reply + / -
Thankyou so much! Instructions worked perfectly.


oki c9600/9800 finally by Anonymous (4/16/07 12:19 AM) reply+2 + / -
working on c9600
Power ON printer while holding "+(up)" & "-(down)" and "help" buttons until “OKIUSER” message apear in LCD....


Re: Oki c5300n drum reset?? by john6664 (4/16/07 6:16 AM) reply + / -
These codes work on the Xante ilumina also - thank you all

John


Re: Re: ReOki 9800 consumables reset code by john6664 (4/18/07 8:21 PM) reply + / -
Xante Ilumina Codes - Same as 9800

1) Power ON printer while holding "+(up)" & "-(down)" and "help" buttons until “OKIUSER” message apear in LCD
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again...



Re: Re: Re: Re: ReOki 9800 consumables reset code by john6664 (4/18/07 8:26 PM) reply + / -
Xante Ilumina Codes

1) Power ON printer while holding "+(up)" & "-(down)" and "help" buttons until “OKIUSER” message apear in LCD
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again...



Re: Re: Re: Re: Re: ReOki 9800 consumables reset code by Andy0078 (4/19/07 5:10 PM) reply + / -
Does not work with oki9600/9800, this procedure reset all but toner. This way you can not reset tonet.


Re: Re: Re: Re: Re: Re: ReOki 9800 consumables reset code by john6664 (4/19/07 7:02 PM) reply + / -
you can't reset the toner it has a chip in it that can't reverse
but you can refill before the chip dies, It will keep the toner alive as long as you refill before it says its empty.
I have reffiled my toners 3 times already. after a refill the display says only 10% left but will print untill you run out.

Just keep some on hand and refill every day or so



Re: Oki c5300n drum reset?? by brucegat (4/19/07 10:39 PM) reply + / -
that's great, but where do you get the replacement toner?


Re: Oki c5300n drum reset?? by john6664 (4/20/07 6:20 AM) reply + / -
cfreinds.com use toner for the 9000 series



Re: Re: Oki c5300n drum reset?? by sandi1904 (5/6/07 11:59 PM) reply + / -
Your procedure Glenn, work perfect.
On my C5300 I test all resets you mentioned and it works perfectly. Thanks for this very good instruction and thanks you to cut my consumable costs so much.

Thank you again.

Aleksander


Re: Oki c9300n drum reset?? by Rob Roy (5/16/07 8:01 AM) reply + / -
Thanks...Thanks...Thanks...I have a 9400 DN that has done 213k prints I bought off Ebay ...The NV Ram reset although very slightly different (but not rocket science) is ezpz...!!

I would like to know if you can get fuser rollers recovered/refurbed and how to re-coat Imaging Drums...All Best printer DIY...jamown@aol.com


Re: Re: Oki c9300n drum reset?? by Anonymous (5/16/07 8:59 AM) reply + / -
>>Rob Roy
I have bought (but not yet tested them) drum rollers for Oki 9000 here: http://farbtoner.com

This is not rebuild drumunit, only the drum roll. Which is great! Don´t change more than necessary.

Do anyone know any other company that sell drum rolls for Oki like this?


Re: Re: Re: Oki c9300n drum reset?? by Anonymous (5/16/07 8:25 PM) reply + / -
Uninet at uninetimaging.com sells toner and drums.

But be warned, changing a drum is a real challange, at least with the Okidata 5000 series printer drum units.

Good luck.


Re: Re: Re: Oki c5300n drum reset?? by Anonymous (6/1/07 9:13 AM) reply + / -
did you solve the question?



Hurray, it works perfectly by Newres (6/13/07 10:00 PM) reply + / -
No need to buy the drum just yet.

It took me about 20 minutes to find this solution and only 5 minutes to process the steps and it worked first time.

The instructions are easy to follow.

Thanks again glenn


Re: Oki c5300n drum reset?? by sergio lucas (6/20/07 2:33 PM) reply + / -
anyone know, if is possible use uninet toner in okidata c5500.....??


Re: Re: Oki c5300n drum reset?? by hhssbb (6/20/07 4:15 PM) reply + / -
Call Uninet. (310)280-9620


Oki c5200 drum reset by Anonymous (6/26/07 5:46 PM) reply+1 + / -
Works fine for OKI C5200

1) Power ON printer while holding "+(up)" & "-(down)" and "help" buttons until “OKIUSER” message apear in LCD
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again...



Reset Oki C6100 toner usage by Jon14 (7/5/07 2:05 PM) reply + / -

I have read thru this thread and did not see anything specificaly related to the C6100 series. What are the recomended steps to reset the toner usage counter for the c6100. Thanks.


Reset OKI C9500 toner. by kereru (7/17/07 9:04 PM) reply + / -
Hi Simply Dan.

According to a user in another forum the reset shown below (which I use on my C7500) will also work for the C9500 printers as well.

OKI think the main board is faulty??? Typical lazy help...

Cheers, Neale (Bay of Plenty, New Zealand).


Resetting consumables for OKI C7500 printer (and other C7000 series).

1. Hold buttons 0 + 1 + 6 + 7 on startup.

2. Press button 0 several times until "DIAGNOSTIC MODE xx.xx.xx" shows.

3. Hold buttons 2 + 3 until "ENGINE DIAG LEVEL 4" shows.

4. Press button 1 to scroll to "COUNTER SET".

5. Press button 2 to scroll through menu items (button 6 scrolls backwards)

6. To alter the value of an item, first press button 3 to select the digit to be altered. The selected digit will slowly flash. (Button 3 moves to the right through the digits. Button 7 takes you to the left.)

7. Then press button 2 to increase the value of the selected digit. Press button 6 to decrease the value.

8. When the changes have been made hold buttons 1 + 3 + 5. The screen will flash three times and then an * will appear on the right of the screen. The new value is set.

9. To leave the counter set menus, turn the printer off.

NOTES:
An "ID" unit is an imaging drum. The life used (shown as pages) doesn't need to be changed. Instead you change the "life limit" to get more use out of the drum. The default figure is 20,000 pages. If you are careful with your drums and keep light away from them they should easily last to 40,000 pages and beyond

Each colour toner counter shows life as percentage used. So a toner showing 30% has used up 30% of its toner. 100% would indicate a near empty toner. This is the reverse of the toner life shown from the "usage menu" when the printer is in normal operation, which shows the toners as a percentage life remaining.

The toner life limit default is set at 100%. Another option to use, instead of changing each toner's percentage life used (i.e. cranking back from 97% down to 87%), would be to increase the toner life limit above 100%. For example, increasing it up to 110%. In practice the OKI printers seem to fairly accurately record the amount of toner used, so an extra 10% might be all you get out of a toner. What feedback can other people offer on how much extra life they get?

If you are swapping over toners or drums from another secondhand printer into your printer, it will not know they are "new" and your printer will still show the existing life values for the old units. If you know the life used in these "new" units you can go into the printer's counter set menu and reset the values so they are more accurate.



Re: Oki c9300n drum reset?? by Anonymous (7/18/07 9:55 AM) reply+1 + / -
This worked on my Oki C5100! Thank you very very very much!!!!


Re: C3200n Consumable Counter Set by adhome (7/25/07 9:15 AM) reply + / -
To enter "ENG DIAG LEVEL2" on C5250 the release seqence is important:

The display shows "Diag Mode 01.02.02 S-Mode" as mention multiple times on this thread.
1) Pressing the "Online", "Cancel", "Enter", "-" and "Back" AT THE SAME TIME
2) After within two seconds the LCD menu will show "READY". If it doesn’t, release button and repress buttons again.

3) The buttons release sequence is important. So, read this before letting go your five fingers: Release the "Enter" button first and THEN the four others. LCD is still showing "READY".

#This is wrong for C5250. The release sequence is important and must #be:
#"ENTER", "BACK", "-" , "Cancel", "Online".
#Now, you have all time the world to continue with step4.

4) Press the "Online" and "Cancel" button at the same time
to enter "ENG DIAG LEVEL2"


Re: Oki c5300n service call 173: Fatal Error?? by Armando Lacerda (8/7/07 6:37 PM) reply+1 + / -
Just called Customer Service. They say it is a power supply error. They asked me to connect it to another outlet and try again. Believe it or not it worked. The printer is back on. Go figure ...


Re: Reset OKI C9500 toner. by Simply_Dan (8/7/07 8:59 PM) reply + / -
Hey, just like to say thanks for the help. It worked great. I've reset the magenta toner to a different level, and will soon see if starts to run out like it normally should.
Appreciate the help.
Danny


Re: Re: Re: ReOki 9800 consumables reset code by Anonymous (8/23/07 9:40 AM) reply + / -
Hi,

I followed the instructions exactly. #'s 1-3 worked BUT there is no “NV-RAM INITIAL” in the menu. Anyone have any ideas what's going on?


Re: Re: Oki c5300n drum reset?? by Anonymous (9/12/07 10:24 AM) reply + / -
Woked perfect, thanks for the great and useful post!


Re: OKI C7200dn maintenance menus by Anonymous (9/19/07 2:46 AM) reply + / -
Hi Caelum,
We have 3 oki 7200. Ive tried your sequence dozens of times, it does not work ?
When I press buttons 1 & 2 together then swith the printer on, nothing happens ?
Any ideas ?
Kind regards



OKI C7200 DRUM RESET CODES by kereru (9/19/07 4:19 PM) reply + / -
Resetting consumables for OKI C7500 printer (and other C7000 series and C9000 series).

1. Hold buttons 0 + 1 + 6 + 7 on startup.

2. Press button 0 several times until "DIAGNOSTIC MODE xx.xx.xx" shows.

3. Hold buttons 2 + 3 until "ENGINE DIAG LEVEL 4" shows.

4. Press button 1 to scroll to "COUNTER SET".

5. Press button 2 to scroll through menu items. (Button 6 scrolls backwards)

6. To alter the value of an item, first press button 3 to select the digit to be altered. The selected digit will slowly flash. (Button 3 moves to the right through the digits. Button 7 takes you to the left.)

7. Then press button 2 to increase the value of the selected digit. Press button 6 to decrease the value.

8. When the changes have been made, hold buttons 1 + 3 + 5 together. The screen will flash three times and then an * will appear on the right of the screen. The new value is set.

9. To leave the counter set menus, turn the printer off.

NOTES:
An "ID" unit is an imaging drum. The life used (shown as pages) doesn't need to be changed. Instead you change the "life limit" to get more use out of the drum. The default figure is 20,000 pages. If you are careful with your drums and keep light away from them they should easily last to 40,000 pages and beyond

Each colour toner counter shows life as percentage used. A toner showing 30% has used up 30% of its toner. 100% indicates a near empty toner. The printer only estimates the amount of toner used, so an “empty” toner will still have a reasonable amount of toner inside. I suggest resetting a 100% (empty) toner back down to 90% rather than zero, and then write the reset details in felt-tip marker on the toner cartridge. You’ll learn how much extra life can be gained from the toners.

An important note: The toner life shown in Diagnostic Mode is the opposite of what is shown in the Usage Menu when the printer is in normal operation. The usage menu shows the toners as a percentage life remaining, so 100% means a full toner.

Neale Blaymires
New Zealand


Re: Re: Oki c5300n drum reset?? by Anonymous (9/20/07 12:13 PM) reply + / -
My printer was making the loud clicking noise in a new drum assembly that I had recently replaced, so i followed the instructions here:

http://www.futuregraphicsllc.com/lit/articles/howard_C5400_0905.pdf

and on page 71, photo #8 you can see the sort of toner transport system, it moves along that thick belt and on the very left of the picture, just under where the red blow tube meets the can of air blower the guy in the picture is using there's a little white spec.. well that spec was covered by a plug of toner that was preventing the belt from moving, and causing the click sound of the "locked" image drum...

I chipped the toner cake out of there and cleaned out that area, then re-assembled the drum unit and the clicking stopped and the image drum could again turn freely.

In order to expose this area of the drum, it's not really necessary to dissasmble the rest of it, just slowly pry off the plastic plate covering the gears.. you see in photo 9 that there are a number of "pressure pins" they aren't glued or anything, they're just pressed in there and with patience the plate comes off fairly easily.. just be sure to remove it evenly, as in work it a milimeter at a time all the way around evenly to avoid breaking it.


Re: Oki c5300n drum reset?? by kereru (9/25/07 2:05 PM) reply + / -
Hi Stormin. What model printer do you have?

See an earlier post by Caelum (10/17/06 6:10 PM) for C7200

>>>> 1) Turn on Printer while holding the 1 & 2 buttons.

Cheers, Neale.


Re: C3200n Consumable Counter Set by Anonymous (10/13/07 2:35 PM) reply + / -
This worked for the C5200N. Set exact Remaining Toner Values.

The Cosumable Counter reset for each toner can be reset to original / actual values (if you know what they are or printed a status page) by performing the following:
Using the output from the status, perform the following calculation, (100-(%remain))=%used, then (%used/4)=%Input Value
Round Down to give you more remaining toner, UP for less.

Enter the printer into the "CONSUMABLE COUNTER SET" mode, then move to the proper toner to modify i.e "K-Toner Value",
Press enter to select this value to change, use ONLINE to increase digit value, CANCEL to decrease digit value, "-" to change selected digit (or was it BACK), Input the calculated %Input Value from above. Press and HOLD "CANCEL and ONLINE" until digits stop flashing, the new value will be stored.

Now, How do I modify the values for DRUM LIFE, FUSER LIFE and BELT LIFE??? I reset them to 100% remaining from a previous reset, but would like to get the proper values set.

- Mr.Gadget



Worked for a c7350 by kereru (10/25/07 1:30 PM) reply + / -
Hi Jerryd.

Scroll back up the page a few posts to (9/19/07 4:19 PM) and read my instructions...

Cheers, Neale.


Re: Worked for a c7350 by Jerryd (10/26/07 11:12 AM) reply + / -
Worked like a champ. Thanks for taking the time to help
Jerry


Re: Re: Oki c5300n drum reset?? by Anonymous (10/27/07 5:56 AM) reply + / -
Many thanks Glenn - I reset the fuser unit using your instructions and it worked perfectly. You've saved me a lot of money!

Alfie in Dublin


Re: oki c5500 reset question. by Anonymous (11/12/07 11:34 AM) reply + / -
This took a lot of button gymnastics to figure out, but I hope it is helpful to everyone with a C5500 (and it might work on the C5800 since it takes the same consumables, but not sure)...

To get the OKI C5500 to keep going (without opening and closing the lid constantly) in spite of toner cartridge & drum life messages:

1) Turn off printer.
2) Hold down "+" and "-" buttons at the same time, and keep them held down while turning printer back on... continue to hold until the word "OKIUSER" appears.
3) Use "-" button to scroll down to "FUSE KEEP MODE".
4) Press "Enter" button, hold for approx. 10 seconds, then release.
5) Press "Enter" button again, followed by rapid release and repress with hold for approx. 10 seconds.
6) Release "Enter" button, then press and let up one more time quickly.
7) You will see "INITIALING" and then "ONLINE" messages.

If you currently have an error message for toner cartridge life, the message will continue to be shown until after you've sent one print job, and then it will usually disappear for awhile. It will stay gone for longer if you have your printer set up so the toner sensor is turned off.

If you currently have a error message for drum life, it will continue to appear, but you will still be able to print.

Beware that you will have to keep a closer eye on print quality (since you are no longer relying on error message to tell you when your toner cartridges are in need of a replacement or refill, or the drum truly needs to be changed or refurbished).


Re: Re: oki c5500 reset question. by Anonymous (11/12/07 11:54 AM) reply + / -
Please note that anytime you turn the printer off, you will have to go through the whole process again when you turn it back on. It doesn't take long though, and will quickly become habit whenever turning on your printer for the day!


OKI 5200 Clicking/gear skipping Noise by billspinali (11/16/07 9:06 AM) reply + / -
Sounds like you people know your stuff, so rather than throwing out my printer, which has very little use, though I would ask for diagnosis here.

Just today my printer started making what sounds like a grinding or gear skipping noise on warm up and printing. So far, it still works.

Your expertise would be appreciated.


oki c5500 reset by Perky (11/17/07 9:43 AM) reply+2 + / -
Dear Anonymous

~~~~ WOOT ~~~~
the 5500 reset worked PERFECT!!!
wanted to personally thank you .... now Im off to slap OKI for making it so tricky




Steps for OKI C7200 maint menus/Differs with C7400 by Anonymous (11/20/07 10:56 AM) reply + / -
There is only a ONE difference on the first step and an extra bit of information between step 1 and step 2 between accessing the Maintenance Menus of the C7400 and the C7200 Printers as explained earlier:

STEPS FOR THE OKIDATA C7400 PRINTERS:

1) PRESS AND HOLD BUTTONS 1 + 5 AND TURN ON THE PRINTER (WHILE CONTINUING TO HOLD THE BUTTONS).
(For Oki C7200 Printers you press and hold buttons 0 + 1 + 6 + 7).

**(addition information) "MAINTENANCE MENU" will appear on the screen within a few seconds. Then about 5 seconds later, "OKIUSER" will appear.

***THE REST OF THE STEPS ARE THE SAME FOR BOTH C7400 AND C7200 SERIES PRINTERS...

2. Press button 0 several times until "DIAGNOSTIC MODE xx.xx.xx" shows.

3. Hold buttons 2 + 3 until "ENGINE DIAG LEVEL 4" shows.

4. Press button 1 to scroll to "COUNTER SET".

5. Press button 2 to scroll through menu items (button 6 scrolls backwards)

6. To alter the value of an item, first press button 3 to select the digit to be altered. The selected digit will slowly flash. (Button 3 moves to the right through the digits. Button 7 takes you to the left.)

7. Then press button 2 to increase the value of the selected digit. Press button 6 to decrease the value.

8. When the changes have been made hold buttons 1 + 3 + 5. The screen will flash three times and then an * will appear on the right of the screen. The new value is set.

9. To leave the counter set menus, turn the printer off.

---> I thought that I would add some help for the next guy who also has a C7400 printer.

------> THANKS A MILLION!!! FOR EVERYONE WHO TAKES THE TIME TO HELP OTHERS IN THESE FORUMS!!


----->Brook<-----



Re: Oki c5300n drum reset?? by tmckinney (11/22/07 11:12 AM) reply + / -
I just found this on the web...
For maintenance and parts manuals for c5500; c5800; c6100

http://printelogy.net

http://compudirect.net/pdfs/parts/partsc5500_c5800_c6100.pdf

Enjoy

God Bless,
Tom


Re: Re: Oki c5300n drum reset?? by Anonymous (11/30/07 12:32 PM) reply + / -
WOW!!!! GOD BLESS YOU!!!! I was at my wits end trying to find a low cost image drum supplier. Trust me , They don't exist. While surfing the net, I discoverd HP laser printers could be reset,and wondered if the same could apply to OKI printers. So I decided to surf a little more and "BINGO" I came across your forum, and Glenn has the answer. I have an OKI c5100 and this technique worked beautifully. Now I'm no tech guy, but I understood everything completely. I hope this forum can help everyone who's having the same problem I had. My hat's of to Glenn and everyone else who contributed to this site.
"KEEP UP THE GOOD WORK"


Re: Oki c3200n by vima1 (12/5/07 12:39 PM) reply + / -
Anyone know what the following error message means and is there a diy solution; LCD message: Service call:163 fatal error


Re: Oki c5300n drum reset?? by brevia (12/5/07 3:54 PM) reply + / -
I have an OKI c5800. I'm getting an error messages that says

SERVICE CALL
980 FATAL ERROR

What's up? What remedy?

thx


Re: Oki c5200 drum reset by Anonymous (12/7/07 11:52 PM) reply + / -
This really works - used on C5250 - Needed Three Image Drums now reset and working perfectly.


Re: Re: oki c5500 reset question. by Anonymous (12/19/07 7:23 AM) reply + / -
To Anonymous who posted the C5500 reset on 11/12/07 11:34 AM...
you are AWESOME!!! It worked beautifully. Another OKI plan to rip us all off on comsumables has been foiled.


Re: OKI 5200 Clicking/gear skipping Noise by Anonymous (12/21/07 10:54 AM) reply + / -
My OKI C5500 does the same thing when the gears on a drum go bad. To figure out which one is causing the problem...

1. Take out all the drums
2. Put them back in one at a time, closing the lid so it will go to warm-up between each color
3. If you hear the clicking/grinding noise after placing in a color, there's the culprit!

If drum was bought recently, you may be able to get whoever you bought it from to exchange it. If not, it's probably just worn out, so time for a new one.


Re: Oki c5300n drum reset?? by MargieC (1/28/08 5:40 PM) reply + / -
Just wanted to thank all of you for posting your expertise and experience to this forum. Saved us a couple of hundred dollars for sure. We reset our 5200n and will surely have extended use on our drum. Thanks again!


Re: Re: Oki c5300n drum reset?? by Anonymous (1/30/08 6:03 AM) reply + / -
Change the Fuser Unit


Re: Re: Oki c3200n by Anonymous (1/30/08 6:06 AM) reply + / -
163 Toner Sensor Error, Color:Black When black toner sensor error has occurred (in factory mode only)
In OKI C3200N


Re: Oki 5900 drum reset?? by gommersheim (1/31/08 12:32 AM) reply + / -
Hello,
we have a OKI 5900 printer.

I do this:

1) Turn off printer.
2) Hold down "+" and "-" buttons at the same time, and keep them held down while turning printer back on... continue to hold until the word "OKIUSER" appears.
3) Use "-" button to scroll down to "FUSE KEEP MODE".
4) Press "Enter" button, hold for approx. 10 seconds, then release.
5) Press "Enter" button again, followed by rapid release and repress with hold for approx. 10 seconds.
6) Release "Enter" button, then press and let up one more time quickly.
7) You will see "INITIALING" and then "ONLINE" messages.

Now we can print a view sites, but then he´s got the error message:

REPLACE IMAGE DRUM ^^.


What can i do please helpl.


Re: Re: Oki c5300n drum reset?? by Anonymous (3/1/08 8:51 AM) reply + / -
Glenn,

I have no techno genes at all - and I was able to follow your instructions for my C5300n. How you ever figured that out, I can't imagine. But, thanks!!!!!
One quick question - how will I know when these really wear out? If my printer starts messing up, how will I know which thing to fix/replace? I am truly technically/mechanically challenged.

Thanks!!!!!!!!!
Rebecca


Re: Re: Re: Oki c5300n drum reset?? by colortoner (3/6/08 10:10 AM) reply + / -
Hi Rebecca,

If you have replace the fuse in the drum unit or installed a new or compatible drum unit and it is not resetting, then you can try the following procedure. However, if your drum unit indicates replacment needed, then you must install a new fuse in the drum. Also, your images will start to become "light" when the OPC drum in the unit becomes worn and you should replace. We do sell these remanufactured units but first try the following:

Counter is not Reset after Replacing a Consumable
Symptom: Consumable fuses are not being blown after repeat replacements. Product(s): Okidata C5100, C5300NCause: Printer may be in Factory Mode as opposed to Shipping Mode. Note: If unit is found to be in shipping mode (correct default setting), then the problem could be with the consumable itself, or the unit.

Resolution: 1) Power on printer while holding both the + & - buttons simultaneously; release when "Okiuser" is displayed.

2) Press + or - until "Engine Diag" Mode is displayed; press Enter and Diagnostic Mode xx.xx.xx will be displayed

3) Press and hold both Enter & On-line simultaneously until Eng Diag Level3 is displayed

4) Press + or - until Local Parameter Set is displayed; release and press Enter

5) Press + or - until it displays Factory Mode; if it displays Factory Mode Twice with an asterisk next to one then it is in Factory Mode; Press + or - until it displays Factory Mode & Shipping Mode on the display; then press and hold On-line & Cancel simultaneously; when it stops blinking an asterisk should be displayed next to Shipping Mode, which becomes the default mode.

6) Power printer off then on to complete the procedure. Additional Info:If changing to shipping mode does not resolve the problem of resetting the counter you probably need to just replace the drum unit. Let me know if I can help further.



Re: Oki 9800,9600,3640.. by Anonymous (3/13/08 12:32 PM) reply + / -
to reset these drums...the reason u cant get to nv-ram is that the version firmware is at version 2.00 to get to nv-ram u need to downgrade frimware to version 1.04 then u will get the nv-ram..from there u will be able to carry on.......can anyone help on a oki c5900?
.


Re: Oki c5300n drum reset?? by jonec (3/18/08 9:38 AM) reply + / -
Where can I get these firmwares for a 9600? Thank you.

> Re: Oki 9800,9600,3640.. by Anonymous (3/13/08 12:32 PM) reply + / -
to reset these drums...the reason u cant get to nv-ram is that the version firmware is at version 2.00 to get to nv-ram u need to downgrade frimware to version 1.04 then u will get the nv-ram..from there u will be able to carry on.......can anyone help on a oki c5900?


Re: Re: Re: Reset codes for CL30 by Anonymous (3/22/08 7:24 AM) reply + / -
Hi Nik
Anyway I could share in those reset codes for the CL30? I'm in Canada.



Re: Oki c5300n drum reset?? by Steptoe (3/28/08 11:22 PM) reply + / -
A cool note of thanks guys..on behalve of the children
I admin a small Primary school on very limited budget..the 5300 drums showing near dead.
Cost to replace it wa better to purchase a new printer..which the office did.
The 5300 was put aside.
After a yr or so I had a bit of spare time, know stuff all about printers, and had a play, and came across this thread on google.
The school has a real cool art teacher now, The printer has been reserrected, and the children are having a ball.
Dont know for how long...drums showed about 16000..posts above go from 25000 to 40000 in practice

But moderators, could u drop the 1st 10 or so posts? I nearly didnt get to the REAL cool info ...
Thanks
Cheers
Steps
Auck, NZ


OKI C5200N Toner/Drum Reset by slushie (5/7/08 2:00 PM) reply + / -
I can confirm these instructions work on a C5200N when getting the dreaded "C DRUM LIFE", "M DRUM LIFE", "Y DRUM LIFE" or "K DRUM LIFE". I've revised them a bit and omitted unnecessary information. Enjoy!

1) Power ON printer while holding + and - buttons until the “OKIUSER” message appears on the LCD.
2) Press + or – button until “ENGINE DIAG MODE” is displayed.
3) Press "ENTER" and LCD will be display "DIAGNOSTIC MODE XX.XX.XX S-MODE".
4) Press + or – button until “NV-RAM INITIAL” is displayed.
5) Press "ENTER" again.
6) "TABLE 1" message will be displayed on the LCD.
7) Press and HOLD "ENTER" until the "EXECUTING RESET" message appears (the "NV-RAM INITIAL" message will blink while you hold "ENTER").
8) Power OFF printer, wait ~10 seconds, and power ON again...

Note: This procedure will reset the TONER, DRUM, FUSER and BELT! When the procedure is done, the printer's LCD should go back to displaying "ONLINE" only. If you have any questions, feel free to contact me at spameaterspameater A_T yahoo D_O_T C_O_M!


Re: Oki c5300n drum reset?? by www.cicekci.asia (5/27/08 10:14 AM) reply + / -
How to enter admibn menu

Method to reset back to default value: The default shipping language for the printer is English. It is possible to reset the language back to English from another chosen language by using the "ADMIN MENU" or by running the "Operator Panel Language Utility" again. To reset the language without using the language setup utility the procedure is as follows:

1. Power on the printer holding down the 'Enter' key until "ADMIN MENU" appears on the LCD display, release the 'Enter' key and then press 'Enter' again.

2. Enter the printer's administrator password followed by 'Enter' (default password is "aaaa"), "OP MENU" will be displayed.

3. Press the '+' key three times or until "LANGUAGE MENU" is displayed and press 'Enter'.

4. The display will show "LANG INITIALIZE EXECUTE", press 'Enter'.

5. When asked "ARE YOU SURE?" press the 'Enter' key.

The printer will now restart in English and "ON LINE" will be displayed when it is ready to print


Re: Re: Re: ReOki 9800 consumables reset code by cesarlorente (7/9/08 4:33 PM) reply+1 + / -
Hello Nik,

Would you let me know also how to re3set the 9800? We have Oki 9600 which is essentiallythe same machine. I see codes for other Oki models on this forum but not sure if they work with 9600/9800.

Thanks for your help.



Re: Re: OKI C5500 980 Fatal Error reset?! by scooner (8/5/08 9:16 AM) reply+1 + / -
Hi Donna I hope you can make sense of this & it works for you, Its taken from service manual.



3.1.2.6 Initializing NVM

This self-diagnosis is used for initializing non-volatile memory.
1. Press the 1 and 5 keys until the self-diagnostic (Level 1 ) mode is entered and [NV-RAM INITIAL] is displayed in the top line. (Key 1 increments the item and Key 5 decrements the item.)

2. The bottom line displays the table number subject to initialization. There are three tables to initialize. Press the 2 and 6 keys until the corresponding table number is displayed. (Key 2 increments the table number and Key 6 decrements the table number.)

Note: Do not use Table 2.
NV-RAM INITIAL TABLE 1

3. The [NV-RAM INITIAL] display blinks when the 3 key is pressed and all items in Table 3-3 will be initialized by pressing the key for 10 seconds continuously.
4. Press the 4 key to end the test. (Status returns to that described in 1.)

Table 3-3 (1/2) Items to Initialize in Table 2

Item to Initialize:

Drum counter
Black
Yellow
Magenta
Cyan
Belt unit counter
Fuser unit counter
Toner counter








Re: Oki c5300n drum reset?? by scooner (8/6/08 10:16 AM) reply + / -
Hi again I just found this, dont know if its applicable to C5300 etc.

How do I reset the fuser life message?
After replacing the fuser in the B6200/B6300 it may be possible to clear the warning message manually, this operation can be performed as follows:

With the power on and the printer indicating "Ready to Print", press the SELECT button and DOWN button at the same time. "Reset Counter Fuser U4" should be displayed.
Press the -> button. Display should now read "Fuser U4 Use SEL to Reset."
Press the SELECT key.


Re: Oki drum reset?? by scooner (8/7/08 9:46 AM) reply + / -
I hve been to a C9300 machine today & sucessfull reset all the consumables using the following.

Oki C9300 series consumables reset procedure

Familiarise yourself with the control panel layout first (see below then follow below).

1, Power on machine whilst holding down 0 1 6 7 keys together, Maintenance Menu is displayed then Oki User.

2, Press 0 until Engine Diag 00.11.02 Shipping is displayed (the numbers may be different)


3, Scroll through the menu using the 1 or 5 keys until N V Ram is displayed

4, Press 6 key until Table 1 is displayed

5, Press & hold 3 key for approx 6 seconds during witch time the display flashes then displays Executing

6, Power the machine off then on again, print out menu map if required & you will note all consumables are reset to 99%


Control Panel Lay Out

(Menu= 0) (Item + = 1) (Value + = 2) (Select = 3)



(On Line = 4) (Item - = 5) (Value - = 6) (Cancel = 7)

This should work no problem & im sure it is the same for most Oki colour printers you may have to play with the buttons if you dont have numbers on them to figure out what each one does.

Good luck


Resetting C9000 series by kereru (8/8/08 2:52 PM) reply + / -
Hi. the key sequence for individually resetting consumables in the C7000 series printers should also work for the C9000 series.

Last year I reset the imaging drum life limits from the standard 20,000 pages to 40,000 pages. Yesterday I had to replace my black drum at 41650 pages. So that doubled the lifetime of the imaging drum.

It had recently started producing faint vertical lines in the images, but there was no horizontal banding at all. Apart from the lines the images were very crisp. I have a suspicion that running out of toner and continuing to print pages may damage the drums. You have to watch the printer like a hawk when printing with reset toner cartridges.

Does anyone know if low toner damages drums?

Cheers, Neale.


KEY SEQUENCE:
Resetting consumables for OKI C7500 printer (and some other C7000 series and C9000 series).

1. Hold buttons 0 + 1 + 6 + 7 on startup ("menu" + "item+" + "value-" + "cancel" buttons). For C7400 printer press 1 + 5 on startup. Other models may have another button sequence.

2. Press button 0 several times until "DIAGNOSTIC MODE xx.xx.xx" shows.

3. Hold buttons 2 + 3 until "ENGINE DIAG LEVEL 4" shows.

4. Press button 1 to scroll to "COUNTER SET".

5. Press button 2 to scroll through menu items. (Button 6 scrolls backwards)

6. To alter the value of an item, first press button 3 to select the digit to be altered. The selected digit will slowly flash. (Button 3 moves to the right through the digits. Button 7 takes you to the left.)

7. Then press button 2 to increase the value of the selected digit. Press button 6 to decrease the value.

8. When the changes have been made, hold buttons 1 + 3 + 5 together. The screen will flash three times and then an * will appear on the right of the screen. The new value is set.

9. To leave the counter set menus, turn the printer off.

NOTES:
An "ID" unit is an imaging drum. The life used (shown as pages) doesn't need to be changed. Instead you change the "life limit" to get more use out of the drum. The default figure is 20,000 pages. If you are careful with your drums and keep light away from them they should easily last to 40,000 pages and beyond. When replacing toners or clearing jambs, have the lid open for the minimum time possible. And NEVER allow direct sunlight onto the printer.

In Diagnostic Mode the toner counter shows the life as a percentage used. A toner showing 30% has used up 30% of its toner, and 100% shows 100% of the toner is used (a near empty toner). But the printer only estimates the amount of toner used, so an “empty” toner will still have a reasonable amount of toner inside. I suggest re-setting a 100% (empty) toner back down to 90% (rather than zero), and then writing the reset details in felt-tip marker on the toner cartridge. You’ll learn how much extra life can be gained from the toners, and have some idea of when the toner will actually run out. It will also remind you weeks later that you have already reset the toner.

Another way of getting more life is to remove the toner and give it some taps on the side. Any toner hung up on the sides of the cartridge will drop down into the bottom. It also spreads the toner evenly along the cartridge, as the toner tends to run out on one part of a page first. Hold a finger over the stirrer port on the left of the cartridge to stop toner dropping on you clothing.

AN IMPORTANT NOTE: The toner life shown in Diagnostic Mode is opposite to that shown in the Usage Menu when the printer is in normal operation. The usage menu shows the toners as a percentage life remaining, so 100% means a full toner. In Diagnostic mode 100% means an empty toner. Very confusing....


I figured out how to disable sensors Oki C5500n by btd (8/22/08 7:21 PM) reply + / -
1)Power ON printer while holding both the + & - buttons until “OKIUSER” message apear in LCD.
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “TONER SENSOR” is displayed
5) Press "ENTER"
6) Press + or - button to change from ENABLE* to DISABLE

To SAVE the DISABLE setting...

Hold "ENTER", "CANCEL" and "ONLINE" all at the same time. That puts a "*" next to DISABLE and saves it.

This fixes the following problems:

1) The random "543:K Toner Sensor Error" message on the C5500n
2) Allows you to refill toner without buying replacement chips for the tonor sensor



Re: Oki c5300n drum reset?? by btd (8/22/08 7:40 PM) reply + / -
One minor correction. Step 4 should read "SENSOR SETTING".


Re: Oki c5300n drum reset?? by P-Co (9/24/08 2:45 PM) reply + / -
I read this post on resetting the consumables on a Xante Ilumina:

Xante Ilumina Codes

1) Power ON printer while holding "+(up)" & "-(down)" and "help" buttons until “OKIUSER” message apear in LCD
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again...

I am in need of getting this to work, but when I get to step 4, "NV-RAM INITIAL" is not in the list of selections. This thread has been of great value, and I greatly appreciate any help you can provide.


Re: Oki c5300n drum reset?? by Steptoe (9/24/08 4:59 PM) reply + / -
From way up the top...this worked for us
"I think I found a way to reset all consumables (drums, transfer belt, & fuser; excluding toner cartridges) using only the menu. Thus, NO FUSES will be required--sorry all you eBay entrepreneurs, you rode this one out long enough! I was experimenting today (bound and determined to minimize my costs), and the following worked to reset all four drums on my C5300n. Hopefully, the steps work for other models as well. So, here goes:

1) Power on printer while holding both the + & - buttons simultaneously; release when “OKIUSER” is displayed.
2) Press either the + or – button until “ENGINE DIAG MODE” is displayed; press the Enter button and “DIAGNOSTIC MODE xx.xx.xx” will be displayed.
3) Press and hold both the - & On-line buttons simultaneously until “ENG DIAG LEVEL2” is displayed.
4) Press either the + or – button until “CONSUMABLE COUNTER SET” is displayed, press the Enter button; you are now in the menu to set various consumables.
5) Press either the + or – buttons to scroll through the various consumables, at the desired consumable (ie. “K-ID UNIT …” for the Black Image Drum Unit) press the Enter button and the last digit of the count will start flashing.
6) Press the Cancel button to decrease the digit amount or press the On-line button to increase the digit amount; press the + or – buttons to move along individual digits in the count.
7) Once the count is at the level you desire (I reset mine to 50), press and hold the On-line, Cancel, & Back buttons (yes, it’s 3 of them this time) simultaneously until the “*” reappears next to the count; you have reset that consumable’s count to the number you specified.
8) Press the + or – buttons to move to the next consumable and repeat at step 5.
9) Once all consumable counts have been set to desired amounts that are below their end-of-life thresholds, you can use the Back, +, & - buttons to exit through the menus (reverse of steps 2 through 4) until “INITIALIZING” is displayed.
10) You're finished! Now log in to the web interface with your browser and check to see the remaining life of your consumables.

Good luck!

-Glenn "



Re: Re: OKI C5500 980 Fatal Error reset?! by georgeq (edited 10/3/08 12:24 AM) reply + / -
This is the one we have been looking for According to Okidata there is no reset code for the fuser. Reason they give is that 99% of the time you get this error, it's indicative of fuser AND Main circuit board failure. Hence no reset. Since circuit board is not serviceable.
Call them up and tell them your problem. Depending on the "age" of your printer, they will offer you some kind on exchange at little or no cost. In other words they will swap out a bare bones printer, no toner cartridges etc. with a new fuser for your broken one.
Number to call is 1-800-654-3282 I got myself a refurbished printer, overnight delivery at no cost.



Re: Reset Oki C6100 toner usage by Anonymous (10/9/08 12:01 PM) reply + / -
I FIND THE WAY TO RESET THE OKIDATA C6100 WITH OUT TO TOUCH ANYTHING INSIDE THE PRINTER OR CARTRIDGES, ALL WHATS YOU NEED IT IS TO USE THE MUWIN.EXE WITH SOME FIXES AND COMMUNICATE THE PRINTER BY THE NETWORK CONNECTION, I DID AND WORKS PERFECT, YOU CAN RESET ALL CONSUMABLES TO CERO WITH OUT ANY PROBLEM.


Re: Re: Reset Oki C6100 toner usage by georgeq (10/9/08 7:34 PM) reply + / -
I will have to try that out some time, never had a printer on a network connection.



Re: Re: Re: ReOki 9800 consumables reset code by Anonymous (11/22/08 8:21 AM) reply + / -
Hi Nik

How do you do drum,fuser & toner resets on the OKI-9800?

Help!

Kind Regards

Harchand


Re: C3200n Consumable Counter Set by Edgard (edited 2/3/09 5:10 AM) reply + / -
hi, i tried the procedure of nono (date 10/19/06) on my c3200n,
but i have a "diag mode 01.10.02 S-mode".
When i do the 5 buttons press i have got always the message
"black drum near life",not the ready msg.
Any hint is welcom. Thanks

Already many thanks for the reply's, i ordered a new k-drum
and shall replace it when needed.
The question is/was, is there anyone with a c3200n diag mode level "diag mode 01.10.02 S-mode" who was able to do
the procedure (date 10/19/06) from nono?

Finaly it works, when your printer gives already f.e: a toner
low msg, then after the 5 button press you get the msg "toner low" instead of the "ready msg" at that time do step 4
of the procedure of Nono (press Online and Cancel at the same time)


Re: Oki c5300n drum reset?? by Anonymous (12/21/08 5:22 PM) reply + / -
OK, FOR EVERYONE TRYING TO DO A TONER SENSOR RESET ON A C5300, HERE IS A STEP BY STEP WAY TO DO IT. {{YOU CAN REALLY MESS UP THINGS IN HERE, BE CAREFUL!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!}}

AT Any point you need out, don't just turn off the printer, use the back button and the menu minus(-) key to escape back to the message "initializing", then turn off the printer!

1 Just like all other instructions, get into the special menu by holding down the menu+ and menu- keys while turning the unit on.
2 When you see the message "OKIUSER" CAREFULLY release both buttons at the same time.
3 Use the menu- or the menu+ to get to "ENGINE DIAG MODE".
4 Press enter. DIAGNOSTIC MODE XX.XX.XX will appear.
5 Now press both the online and the back buttons, and "ENG DIAG LEVEL 4" will be displayed.
6 Press enter.
7 Press menu+ twice to "ENGINE PARAMETER SET 2"
8 Press enter.
9 Press menu+ twice to get to "TONER SENSOR ENABLE" (with a * in the lower right hand of the display window.
10 Press enter and the word "ENABLE" will begin to blink, indicating it can be changed.
11 Press menu+ and the word will change to "DISABLE", still blinking. This is a toggle, make sure to not hit the button twice.
12 This is the important step: simultaneously press the online, cancel, and back buttons, and let them all go simultaneously. this sets your selection.
13 There are other things that can be done here in the same fashion, but that is out of the scope of this document.
14 Use the "BACK" and the "MENU-" keys to back out all the way to the message "INITIALIZING", then power off, wait 10 seconds, and power back on.

Hopefully this will help some of you!

THIS PROBABLY WONT HELP IF YOU HAVE PHYSICAL DAMAGE TO THE TONER DRUM.


Re: Okidata MUWIN.exe & instructions by hectorhroa (1/10/09 3:14 PM) reply + / -
Sorry I been out for 2 months, if some body need the file MUWIN.exe, please put your e-mail to contact you or if some body know how to up-load the file for every body please put the instructions for me, thank you.


Re: Oki c5300n drum reset?? by Anonymous (1/28/09 10:16 PM) reply + / -
I know the muwin.exe works well to reset the okidata printers consumibles before the printers are locked, but you have to do this reset when you refill the cartridges toner before the printer say low toner cartridge, other ways muwin.exe don't help you at all, this works well to reset all other consumibles on your printer too, I have a C6100 okidata printer and this program save me a lot money because has 4 diferent color cartridges toner, each one cost brand new originals $155.00 dollars plus shiping etc, etc. All total amount probably $700.00 to $750.00.
I just got all set refill in great glosy quality for only $150.00 dollars no microchip needed because muwin.exe do the rest, this program works for different models too.
you need the microchip "ONLY" if your printer become locked saying low toner or "belt life warning", all what you need to do it is to act before the problem to really save money, good luck guys


Re: Oki c5300n drum reset?? by Anonymous (1/28/09 10:41 PM) reply + / -
Be carefull about MuWin.exe for download from http://files.filefront.com/MuWinexe/;11954781;/fileinfo.html THIS IS NOT THE ORIGINAL MUWIN.EXE and this is not for okidata printers, I downloaded to compair this program and it is something different inside. PLEASE DON'T DOWNLOAD TO USE WITH YOUR OKIDATA PRINTER, THERE IS A WEIRD FILES INSIDE.


Re: Oki c5300n drum reset?? by Aro (2/3/09 3:00 PM) reply + / -
MuWin 1.18.1 and reset Toner + Service Manual.
http://files.filefront.com




Re: Re: Oki c5300n drum reset?? by Anonymous (2/10/09 12:28 AM) reply + / -
Good stuff Aro

This is the MuWin (works with C5800 as well). Do you know the key to reset the toner/drum?




Re: Oki c5300n drum reset?? by pimpern (4/1/09 10:09 PM) reply + / -
hello community

Oki c3300n drum reset

thus

the manual for oki c3300n

http://fileload.us/hnijv92oyjky

good luck

gruss mario


Re:Oki C3400 toner sensor error - HELP!! by Tree in KY (4/22/09 9:05 AM) reply + / -
I have a C3400n printer and am getting so frustrated with the toner sensor error. I have tried taking out the cyan toner and drum assembly, but I am lost when I try to find the parts refered to in a picture description for cleaning the sensors.

Any help? I need to print a bunch of stuff for our school and cookbook we are selling and am stuck totally!

Also, any directions for resetting the drums in a C3400n?

Thanks in advance for any and all help! I appreciate it!


Re: Re: Okidata MUWIN.exe & instructions by Esref (6/7/09 12:40 AM) reply + / -
you can upload by this way.
first zip the file
then goto any upload site like rapidshare.
then upload and get the download link after upload.
then please post it here :)


Re: Oki c5300n drum reset?? by homebus (6/13/09 6:34 AM) reply + / -
RS Fuses are discontinued on old number in UK

New RS details as follows

RS Stock No. 541-3237

bag of 10 £6.60


Re: Re:Oki C3400 toner sensor error - HELP!! by Anonymous (6/18/09 11:46 AM) reply + / -

The toner sensor error on the c3400 can be cleared by removing the obstruction on the drum.

all the pictures online are useless, so let me try to explain.

if you remove the drum from the printer the right side has a cut out window, and sometimes a little black piece of plastic on the inside slides down and blocks it. just take a paper clip or something and push the piece of plastic back up out of the way. you should be able to see a green circuit through the window.

that's it. just put the drum with toner back in printer and you should be all set.

it seems that if the toner sensor can not be read, the system will just stop, it will not continue to check everything else.

hope this helps.




Re: Re: Oki c5300n drum reset?? by mikedeni (8/16/09 12:54 PM) reply + / -
OKI c5200 worked like a charm, reset all to 100%!! Thanks Mr. Kim!

1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

All toner, drum, fuser and transfer figures return to 100%.



Oki C3450n drum reset?? by John Silver (8/24/09 8:26 PM) reply + / -
At me printer OKI C3450. It is necessary to dump the toner counter. Prompt, as it can be made. Also give, please, the working reference to program OKI Maintenance Utility. Or send on my E-mail: dflbv@mail.ru. Thanks.


Re: Oki c5300n drum reset?? by mesilva1 (8/25/09 8:55 AM) reply + / -
Does anybody know of a supply source for Oki es3640? I need toner and image drums. Are there rifill kits available? Any comments or info will be very usefull and highly appreciated


Re: Oki C3450n drum reset?? by thepito (9/23/09 3:23 AM) reply + / -
Hello.

I upload the program. I have the same printer than you. Now
I still have the original toners.Tell me if you could reset the toners or the printer.

Email Thepito@hotmail. com

Program MUWIN
http://rapidshare.com/files/283859143/Maintenance_Utility_Win.rar

Bye


Re: Re: Oki 9800,9600,3640.. by Anonymous (10/2/09 6:11 AM) reply + / -
ciao vorrei sapere come fare per resettare il drum e il toner della stampante oki 9600 grazie


Re: Oki c5300n drum reset?? by Jjanson (10/8/09 12:12 PM) reply + / -
I have 2 print jobs in the queue of my OKI 5500n that I can't cancel or delete. I stays locked in "deleting" mode, and I cannot print to the printer from anywhere on the network. I have tried cancelling from all desktops including the one that sent the print job. How do I get these jobs out of thw queue and free up the printer?


Re: Re: Oki c5300n drum reset?? by Anonymous (10/9/09 6:40 AM) reply + / -
on the PC that sent the job what port is the printer connected to?

Check that it is not a shared printer on someone elses PC. If it is then it is that PC's spool queue you need to clear.

If it is networked via an IP port directly to the OKI then it is the machine that sent the job that needs to clear the print spooler queue

instructions for this at http://www.topfreestuff.com/printSpool.shtml



Re: Oki c5300n drum reset?? by Jjanson (10/9/09 8:22 AM) reply + / -
Thanks for trying, but found the folder empty. Any other ideas?


Ok1 C6100 by Anonymous (11/4/09 5:58 AM) reply + / -
How do you reset the consumables in Oki c6100 through the muwin? Thanks for the help


Re: Oki c5300n drum reset?? by sammyjoe71 (11/5/09 12:13 PM) reply + / -
I have a xante cl30 HSE (oki c9500). The original transfer belt broke and was replaced with a brand new OEM part. New belt unit apparently did not auto reset the machine. Almost immediately I got "Belt Near Life" message. After approximately 1500 prints got "Belt Life 356: Replace Transfer Belt" message and machine is totally disabled.
Using codes from this post works great to reset all counts to 0%, but I still have this transfer belt thing going on.
Anybody have a clue?
Thanks!


c9000 belt life by kereru (11/5/09 5:18 PM) reply + / -
How many pages is the belt life showing? And what is the "Life Limit" set for the belt? Cheers, Neale.


Re: Re: Okidata MUWIN.exe & instructions by ssselect (11/8/09 7:01 PM) reply + / -
i have an OKI 6100 and I can't figure out how to reset the drum counters. . . How would I get muwin.exe and once I get it, how do I use it?


Re: Re: Re: Okidata MUWIN.exe & instructions by Anonymous (11/9/09 12:47 PM) reply + / -
I am having the same problem with OKI 6100? Anybody know?



Re: Re: Re:Oki C3400 toner sensor error - HELP!! by Anonymous (11/12/09 10:40 AM) reply + / -
YES!!!! thank you very much this solved my flashing amber light issue after replacing all the toner cartridges


Oki c6100 Fuser Lock Error by slammy (12/15/09 12:44 AM) reply + / -
My mistake was probably grabbing the box of old paper from the bottom of the filing cabinet. Soon after the printer reached these sheets, the edges began smearing the printer locked up. I now have a "Fuser Jam 2" "Fuser Lock Error" error in maintenance mode. Reading through the comments here, it sounds like I might have a chance to clean it before buying a new one. Can anyone step me through this?

Thank you,

Slate


Anyone got any idea on how to do this to a C5600 by Collateral (12/16/09 2:39 AM) reply + / -
It seems like I'm the only person owning a C5600! Has anyone got any idea how to reset the toner on this printer? Thanks, any help is appreciated.


OKI 5800 Drum reset by GeorgV (12/29/09 10:27 AM) reply + / -
I have MuWin.exe, but I can't find the option to reset counters.
I need to reset the drum's counters
Can You help me Pls.

Georg


Re: Oki c5300n drum reset?? by Anonymous (1/5/10 10:33 AM) reply + / -
I have an Oki 3300. I have changed the oners ad the fuser unit and still the red triangle light keeps flasing and i can't print?
wy would that be



Re: Oki c5300n drum reset?? by tolale (1/7/10 10:04 AM) reply + / -
I try to reset the drum cunter of max OKI 5950dn.
I follow this points:

1) Power on printer while holding both the + & - buttons simultaneously; release when “OKIUSER” is displayed.
2) Press either the + or – button until “ENGINE DIAG MODE” is displayed; press the Enter button and “DIAGNOSTIC MODE xx.xx.xx” will be displayed.
3) Press and hold both the - & On-line buttons simultaneously until “ENG DIAG LEVEL2” is displayed.

Every thing works. But when I press the - and the Online Buttons when DIAGNOSTIC MODE is displayed the menue showes no reaktion.
Are there any other key-combinations?

tolale


C6100 reset with out using muwin by sickora12 (1/9/10 8:44 PM) reply + / -
I have new toner in but it still reads toner empty.

1) Power on printer while holding both the + & - buttons simultaneously; release when “OKIUSER” is displayed.

2) Press either the + or – button until “ENGINE DIAG MODE” is displayed; press the Enter button and “DIAGNOSTIC MODE xx.xx.xx” will be displayed.

I can't get past this point. Please help


Re: Oki c3530 chip reset?? by gazb87 (1/15/10 5:10 AM) reply + / -
Hi does anyone know how to override the chips oon the c3530 model?

Thanks Gaz


Okidata c5300n clicking noise and cover open error by OkiProbs (1/25/10 4:19 PM) reply + / -
Hello.. It all started with trying to cure the "clicking noise when running from my c5300... I also have two 5150s for my small business. When swapping ALL the toner drums... the noise would go away. I saw the thread on cleaning the gears in the drum and did so on all units. Now I am getting a cover open error, even when the cover is closed. Please Help!


Re: Oki C3530 reset?? by sdqwqw (1/27/10 12:12 PM) reply + / -
how do i reset the C3530 ?
ow can i get in the menu ??? (pres the menu butten doe not work


Re: Oki c5300n drum reset?? by kereru (1/28/10 11:00 AM) reply + / -
Hi. I'm not familiar with the c5300, but your best bet is to find the micro-switch which detects the lid is open and trouble-shoot that. OKI often use opto-coupler switches: sometimes a squirt of compressed air into the opto-coupler sensor will remove toner which may have lodged inside and prevented it working properly. Another trick is to disconnect and then reconnect the switch. I had a sensor switch acting up inside a duplex unit and reconnecting it solved the problem.
Cheers, Neale (New Zealand)


Re: Oki c5300n drum reset?? by Kate R (2/8/10 4:02 AM) reply + / -
We have an OKI B410d.

Does anybody know a way to reset the drum life and the toner life on this model?

This printer is costing our (small) business a fortune.

Thanks very much, Kate


Oki 7300v2 drum reset?? by Stormin (2/27/10 4:34 AM) reply + / -
Can anyone supply the reset codes for this printer?
Kind regards
KFT


Re: Oki c5300n drum reset?? by kereru (2/28/10 5:57 PM) reply + / -
Have you tried the instructions from my previous post (8/8/08 2:52 PM)


Re: Oki c5300n drum reset?? by MrDrap (3/5/10 3:21 AM) reply + / -
@-Glenn PERFECT!!! works fine to reset drum and TONER!!!


Re: C3200n Consumable Counter Set by Claus Just Rasmussen (3/14/10 1:21 AM) reply + / -
OKI C3200N, firmware 01.10.02 (or at least it tells me "01.10.02 S-Mode") - and network is ok after this :-)

Nono's description works perfectly, please note though, that the printer do not show "READY" in step 2. Instead it will cyckle through the toner status' - just press ENTER anyway. It works!

Thanks to Nono!

Wondering if this could possible be done using the webinterface too? (probably not)

//Claus



Re: Oki c5300n drum reset?? by jraymer (3/26/10 9:41 AM) reply + / -
I have a c9500. Does anyone know how to change the Diagnostic Mode from Factory to Shipping?? Thanks!!


Oki c6100 transfer belt reset by glee (3/30/10 12:00 PM) reply + / -
Dose anybody know how to clear/reset the count on a transfer belt for a c6100?


Re: Oki c6100 transfer belt reset by Anonymous (3/30/10 12:58 PM) reply + / -
I have a xante cl30 (oki c9500). I had a T. belt reset issue as well. This machine has a tiny fuse on the transfer belt that is supposed to blow when the transfer belt is installed. When the fuse blows, it resets the T. belt life count to 0. Replacing the fuse and reinstalling the T. belt solved my problem. I found the fuses @ Fuseco in Atlanta, GA. Hope this helps you.


OKI C3400 by Anonymous (4/15/10 9:23 AM) reply + / -
I have replaced black toner and cartridge in machine. When it is turned on the machine cycles and then the amber light goes on and flashed every second. it says black toner sensor error. If i cheat the top cover open the color drums lift up but the black toner cartridge does not move. What the the reset button on the back of the machine for? Thanks for the help.


Re: Oki c5300n drum reset?? by ciro392 (5/9/10 1:46 PM) reply + / -
Hi all-

Does anyone know how to fix a problem with the NIC card menu disappearing after trying to reset the drums???

I cant connect through the network.

Any help please

Thnaks


C6100 FATAL ERROR 980? by SIRSHTHD (8/23/10 10:03 PM) reply + / -
ANY IDEAS WHAT THIS IS AND IS IT RESETTABLE


Re: Oki c5300n drum reset?? by nivek (8/24/10 5:42 AM) reply + / -
Fuser wrap error. Means paper got stuck in the fuser probably wrapped around one of the rollers. Sounds like you will have to replace the fuser. Most likely one of the rollers is starting to deteriorate cuasing the paper to stick to the roller.


Re:Reset belt Oki c3200 with no lcd display by joegarzf (8/31/10 11:47 PM) reply + / -
How do i reset my oki c3200 with no lcd display? Help please


Re: Oki c5300n drum reset?? by wea (9/6/10 3:21 PM) reply + / -
How to enter ENG DIAG LEVEL2 on the C5650?


Re: Oki c5300n drum reset?? by COSTALONES (9/6/10 4:48 PM) reply + / -
To reset the drums of a 9600, 9650 or 9650 oki, you need

Option A: PU versión v00.05.04 or minor. Then apply the reset via menu.

Option B: A special fuse that you have to change at the drum.

Anybody knows how to downgrade de PU versión.

Thank in advance


Re: ReOki 9800 consumables reset code by Pablozee (9/6/10 5:05 PM) reply + / -
Hi Bruce
Would you share the reset procedures for the Xante CL30 please.
Thanks
Paul


Re: Re: Oki c5300n drum reset?? -> It is easy!!! by tolale (9/6/10 11:48 PM) reply + / -
Don't open the drum case! It is much easier and you need no tools.

Read this: http://www.fixyourownprinter.com/forums/printer/67132#1
You need only the glass fuses ans the thin kables. You find the contacts on the right side of the printer case (they fit directly to the contacts of the drum unit). The contacts have a little hole, where you can fix the kables.
After connecting the fuse switch on the printer. About 20 seconds later the fuse blows and the drum unit is resettet.

When you make a short circuit a furse - error occurs.

Happy resetting!

tolale


Re: Re: Okidata MUWIN.exe & instructions by tvameijde (9/20/10 1:40 AM) reply + / -
Hallo Hector,
Can you please send me a copy of the muwin.exe file. I live in Germany. Please send it to tvameijde@gmail.com.
Thank you in advance.
Greetings Catharina van Ameijde


Problem with Oki c5400n drum reset?? by tw1g (11/20/10 4:06 PM) reply + / -
I have an OKI c5400dn showing "X DRUM LIFE" for the three colour drums.

I have been trying to follow the 'Consumable Counter Set instructions by Nono', but do not seem to be able to get beyond the display of "DIAGNOSTIC MODE / 01.02.07 S-MODE". I have tried many different combinations of buttons to get into 'regist mode' without success.

I have also had no luck with an alternative suggestion, I have been unable to find any key combination that gets me to "ENG DIAG LEVEL2".

I would appreciate any suggestions.

Thanks

Twig


Re: Oki c5300n drum reset?? by Edgard (11/21/10 2:47 AM) reply + / -
Finaly the procedure worked for me on my c3200 oki printer.
After the msg "Diagnostic mode" and you press the 5 button keys,
you see the msg READY or one of the messages "DRUM live" etc.
Release the buttons in sequence enter-back-"-"-online-cancel,
press asap online and cancel at the same time.
If you were lucky you got the ENG DIAG LEVEL 2 , success.


Re: Oki c5300n drum reset?? by tw1g (11/21/10 4:49 AM) reply + / -
Thanks Edgard, that worked a treat!


Re: Oki MuWin.exe by TFP Maintenance (11/22/10 2:08 PM) reply + / -
Anybody know where to get the MuWin.exe utility? please email me, psuedoguru@yahoo.com


Oki MuWin.exe by TFP Maintenance (11/22/10 3:40 PM) reply + / -
OK, I have the MuWin.exe file, I can grab the counter information from the printer, I think I've identified the hex values that represent the drum counter values, now, how do I push new values back to the printer? I have an Oki C9600N.

TIA.


Re: Oki c5300n drum reset?? by btfsc (11/24/10 1:29 AM) reply + / -
TFP Maintenance here is what I have found so far.

The MU_WIN saves the eeprom as a bin file when using the "Board Replacement menu,PU board replacement,Upload and save PU board setting value" menu item.

You can input the serial number of your printer for the ID and it will save a file with this format on my C5400 PX724N_XXXXXXXXXX_EEPROM.bin the X represents the ID number you entered.It saves it in the \ProgramFiles\Okidata\MaintenanceUtility directory if you installed the program, don't know where it's saved it you run it without installing.

It you save a text version with the above menu item it matches the file saved under "Printer maintenance,Counter maintenance function" menu item.

If you can find the locations to modify in the bin file you can use the "Board Replacement menu,PU board replacement" menu item to save it back to the printer with the "Download the saved PU board setting value" menu item.

I think I will reset all the drums and compare the bin file and see what changes.

Those of you who want to try this may brick your printer if you choose the wrong location to change or use the wrong values.


Re: Re: Oki c5300n drum reset?? by blamberg (1/4/11 5:22 AM) reply + / -
The drum counters are in plain hex, but not the toner values. In Muwin a counter value of 100 = empty, 0 = full, i presume. No such values in the bin file. Did anyone have luck in decoding? (C3600)


Re: Oki c9650 drum reset?? by magaldesign (1/29/11 3:08 AM) reply + / -
Are this stoptoner.com kits for reset drums good?


Re: Oki c9650 drum reset?? by magaldesign (1/29/11 3:11 AM) reply + / -
Are this stoptoner.com kits for reset drums good?


Re: Oki c5300n drum reset?? by Printer_wizard (2/21/11 3:08 PM) reply + / -
Hey guys

Im having the same issue with the k drum life on a Oki C5750
I replaced it with a new genuine drum and the message still wont go away.

I have tried averything above but things must be a bit diff with this model.

I can get into diag mode fine, but cannot get into a 2nd level diag or find the nv reset..


Re: Re: Oki c5300n drum reset?? by Emmanuel ahligo (3/21/11 10:09 AM) reply + / -
Hello
Thanks so very much, i've tried the OKI c5300 drum and toner reset and it did work.Thanks for the update.
All the best.



Re: Re: Reset Oki C6100 toner usage by OldSkoolVinyl (5/12/11 7:33 AM) reply + / -
So wheres the software??

upload a link!


Re: Oki c5300n drum reset?? by DF1PAW (5/13/11 12:16 PM) reply + / -
@OldSkoolVinyl:

Try http://www.okisa.co.za

Anyone success with decoding the PU Flash dump?
I suspect the Total PageCount at 00b6h and 00b7h in the text file. There seems to be some additional 76 byte header in the binary file (compared to the text file).

The 76 byte header for me:
4A 00 00 00 00 02 00 00 50 58 37 32 34 4E 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 BE 18 00 00

The .bin file's size is 588 bytes for my Oki C5250n - may be this is printer independent. I hope to try with a C5650n next week...

I suggest collecting and comparing several PU Flash files.
Educated guesswork: I hope the variables could be determined this way and an "full toner, belt, drum" file created for upload.

So I request you to provide some PU Dumps via eMail for comparison.


Regards,
Andreas Weller


Re: Oki c5300n drum reset?? by klawtrax (8/27/11 2:34 PM) reply + / -
I would like to use the ten step near the top of this post to reset all counters but here is my problem. We had a surge and the display is shot. Can anyone count the button pushes that will take me through the ten step procedure so that it can be done without the display? Thanks for any help.


oki 9850 problem .. by guidophone (10/11/11 12:37 PM) reply + / -
Hi.

I have a LUCIDIOM 9850 which is an OKI 9850 rebranded. We went in to the maintenance menu to check the machine's humidity reading. I have a feeling somebody changed the OKIUSER value and now the machine is saying 'incompatible toner' for all the colors and won't operate.

In diagnostics mode, it says invalid toner group.

How do we restore the machine to operational?
Can we reset the nv-ram. It doesn't appear on the diagnostic menu
What do we set the okiuser value to?

Please advise!

Guido


Re: Oki c5300n drum reset?? by francisco navarrro (10/16/11 10:29 AM) reply + / -
alguien me puede decir como resetear los tambores y el fusor de una oki c3520 mpf?

cuestan un pastón, y no está la vida como para derrochar. muchas gracias


Re: Re: Re: Re: Oki c9300n drum reset?? by borlix (10/28/11 1:12 PM) reply + / -
Hi - Change drum is easy, remove the manuals of uninetimaging

I Recycling
I have a lot of drums and recycled for oki c5000 series


RE :OKI 5500n by edkaeser (edited 7/25/12 8:17 AM) reply + / -
I have an OKI 5500n and really love the quality of print. However, lately, the red seems to not be printing well and there are a couple of lines running through the image whenever the red is used.

What maintenance measures can I take to clear the problem.

Thanks so much everyone! PLEASE HELP!

Ed Kaeser


OKI 8800 Toner level reset by Vi7ER (5/22/12 7:59 AM) reply + / -
Hi,

I've been pouring over this thread and several others in an attempt top reset the K Toner level on our OKI C8800n.

I can get into the Maintenance menu (although it asks for a password - which I have figured out) and then scroll to ENGINE DIAG MODE, press enter then see: DIAGNOSTIC MODE 00.00.33 S-MODE.

After this however I cannot get to ENG DIAG LEVEL 2 and a menu option that sets consumable levels.

If anyone has an 8800 and knows how to do this I would really appreciate it. I have a near full K Toner here that stands to be wasted if I cannot figure it out!


Re: Oki c5300n drum reset?? by Sybil (7/16/12 8:53 AM) reply + / -
Maybe You can help Me with my OKI C7300? I cannot find anywere instruction and all above are not working with my oki...


Re: Oki c5800 toner reset?? by mikeyto (7/22/12 9:52 AM) reply + / -
Can anyone help me reset the toner for my c5800? Thanks in advance


OKI 5500n HELP! by edkaeser (7/25/12 8:18 AM) reply + / -
I have an OKI 5500n and really love the quality of print. However, lately, the red is not be printing well and there are a couple of lines running through the image whenever the red is used.

What maintenance measures can I take to clear the problem.

Thanks so much everyone! PLEASE HELP!

Ed Kaeser


Re: Oki c5300n drum reset?? by HMC (8/17/12 12:19 AM) reply + / -
How about C5700n ?
It's not working for me at step "DIAGNOSTIC MODE / xx.xx.xx S-MODE".
Please help me.


Re: Oki c5300n drum reset?? by Ikke342 (4/3/13 11:25 AM) reply + / -
Pleeeaase someone knows how to go to the menu @ oki C3530 mfp?
need help


Re: Oki c5300n drum reset?? by ibantn (8/28/13 12:04 PM) reply + / -
Please let me know if you have a solution for a OKI MC361 printer


Re: Re: Oki c5300n drum reset?? by Octorilla (9/16/13 1:27 PM) reply + / -
Glenn,

Thank you - It worked to sheer perfection!

Now I just have to figure out to get my Kyocera working.

-Dave


Re: Re: Oki drum reset?? by jadielmota (11/16/13 12:16 PM) reply + / -
Hello, do you know how to reset the consumables for the OKI MB260?


Re: Re: Oki c5300n drum reset?? by jadielmota (11/16/13 12:19 PM) reply + / -
Hello, do you know how to reset the consumables for the OKI mb260?


Re: Re: Oki drum reset?? by jadielmota (11/16/13 12:21 PM) reply + / -
Hello, do you know how to reset the consumables for the OKI mb260?


OKI C7300 stuck on Factory Mode by thamel (6/2/14 11:39 AM) reply + / -
I have a OKI C7300 with a 163 Fatal Error. I am not able to find the right combination to change Diagnostic Mode from Factory to Shipping. Can anyone help?


Re: Oki c5300n drum reset?? by kereru (6/2/14 1:13 PM) reply + / -
Hi. From my post earlier in this forum:

Resetting consumables for OKI C7500 printer (and other C7000 series and C9000 series).

1. Hold buttons 0 + 1 + 6 + 7 on startup.

2. Press button 0 several times until "DIAGNOSTIC MODE xx.xx.xx" shows

My OKI service manual indicates a 163 error is something to do with the K toner. You may have a faulty toner level sensor. Sometimes disconnecting and reconnecting the plug to a sensor will fix the problem.

There is also step 3 for the list above:
3. Hold buttons 2 + 3 until "ENGINE DIAG LEVEL 4" shows.

Cheers, Neale.


Oki 5100 C5200 etc Drums are they interchangeable by raydicks (6/30/14 9:48 PM) reply + / -
I have 4 yellow drums oki # 42126601 but I need 2 black and 1 cyan and 1 yellow.

Looking at them they all look exactly the same. so if I put a new unused yellow drum in the Black slot and put black toner in it will it work?

Thank you


Re: Oki c5900n drum reset?? by Eros (11/26/14 9:44 AM) reply + / -
Oki c5900n drum reset??

Thx :)


Post to this thread:

User:
Email:
Notify me if someone responds

Icon:            
Subject:
Message:



© 2012 fixyourownprinter.com, All posts belong to their respective posters