Anonymous

asked Mar 29, 2009 at 6:59pm
Unknown Printer

Canon pixma mp 198 reset

Hi guys i'm new in the forum can someone help me how to reset my mp 198 canon...it says "shock observer full"...i need the method how to reset my printer pls help me..thank in advance
Alhamdulillah .....it work .....
by unknown on May 18, 2010 at 10:08am Add comment
thx...its works ;)

keep it up :)
by unknown on May 25, 2010 at 5:23am Add comment
I Quoted this message from canon Mp 150 reset..does this work with canon Mp 198 too?Or is there other method of resetting my printer?

"This is actually a very easy fix. Two absorber pads are located on the right side of the printer, under the ink cartridges. With the printer on, lift the top to expose the cartridges. They will automatically move out of the way. You can move them to the left side by hand if the printer is not on. You will probably need a flashlight to see the pads. They each sit in a rubber retainer. The pads can be removed very easily and cleaned. Take the pads out of the retainers with tweezers. They clean up nicely with warm water but you can use something like Simple Green if they are stubborn. It is best to use a spray bottle (on stream) and blast it through the pad until it is white. Sometimes just putting it under a running faucet will do the trick. If there is ink in the rubber retainer after taking the pad out, it can be cleaned up with a paper towel. Put the pads back into the retainers and you have successfully cleaned the ink absorbers. Now you may have to reset the error message so you can get back to printing. This is how to do it.

How to clear E27 Code

* With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
* When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
* When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
* When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset. "

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)




Does this work with canon pixma Mp 198 too?I need a confirmation before i try it out with my printer..Help me pls...
by Anonymous on Mar 30, 2009 at 12:03am Add comment
I've tried this on my mp210 but I'm pondered about something.

When it enters the service mode the display indicator shows the 0 instead of the usual 1 (as 1 copy) and the power button is green. When I press the stop button the power button goes off and the system notice led shows orange. If I press stop again the power button goes green again and the system notice LED is turned off. I've figured this is what you meant that the LED goes green/orange. But what should I press or should I press anything at all when I'm choosing the options? Does it just work automatically each time you select the certain option? (by pressing the stop button the desired number of times) - nLike
you can visit or leave a msgs on my e-mail ad.may be i can help you about your [email protected]
by jireh_29 on Oct 14, 2009 at 10:49pm Add comment
ink absorber is full flashes in my screen whenever i have something to print, how can i fix this problem? please help.... - Anonymous
IP4680 AND MP198/190/210 RESETTER
http://tipidpc.com/viewitem.php?iid=4611124
by unknown on Nov 26, 2009 at 3:23pm Add comment
someone can help me about reset canon pixma MP190 not mpc!!! thanks
by unknown on Dec 5, 2009 at 12:25am Add comment
by wengseng on Jan 15, 2010 at 7:00am Add comment
I have seen this procedure but my printer don't have another led except green led. I've tried this one but it doesn't work. Someone had another solution???

by unknown on Jan 15, 2010 at 11:23pm Add comment
i also have follow the in truction to reseting the printer mp198 but still didt work... haiz so dissappoint - Anonymous
just one led only , tat lcd can change green and orange color
by wengseng on Jan 16, 2010 at 3:28am Add comment
I have a PIXMA MP190, the printer have just a green led, it doesn't change and they aren't tat LCD! The power botton is the led!

I 've tried this procedure:


CANON MP190
Reset Waste Ink full canon

1. Enter SERVICE MODE. By pressing Menu Copy Scan Copy Copy
2. Select TEST MODE.
3. Select [8] PRINTER TEST in TEST MODE.
4. Select 3. [EEPROM CLEAR].
5. Select 0. [INK COUNT].
6. Press the [Set] key.
7. Press the [Stop/Reset] key (returning to the state of
3)), and then press the [ON/OFF] key

After reset manual now remained the reset permanenly using

but it's for MPC 190 not MP 190 pixma :

I'll find this one:

Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER
button.
(3) Release the RESUME button, Next press and release the RESUME
button two(2) more times in
succession. Note: you are still holding the POWER button). The
printer's carriage will "reset"
or move momentarily. If the above was properly performed the
printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink
counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point -
However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to
"set" the change, and return to the top of the function selection menu.
Press the POWER button again to restart the printer.


I can do this procedure, it seems work but the error E27 appears again.



by unknown on Jan 17, 2010 at 10:20pm Add comment
i'll try it. it's not worked
by Anonymous on Feb 18, 2010 at 5:41pm Add comment
how should I fix my canon pixma 198 ? the screen shows INK ABSORBER IS FULL.
by unknown on Mar 5, 2010 at 3:01pm Add comment
Did u see the explanation above? try it! I think that it's the same error as E27! good luck
by unknown on Mar 7, 2010 at 10:23pm Add comment
how can i reset mp198 canon?..pls help me
by Anonymous on Mar 21, 2010 at 10:36pm Add comment
bos aq punya printer canon mp198 E27 carax gmna nc
by unknown on Apr 6, 2010 at 12:18am Add comment
error code5 appeared, alarm lit on, black and colour lit flash, how to reset, I can't enter service mode as I can't identify which is the menu button. unable to remove the waiste inke pad out to wash as they are too soft, it could be broken if I forced it out, have tried to suck the waiste ink with tissue, error code still there
by unknown on Apr 11, 2010 at 1:42am Add comment
i have reset but still appear E27 please help me sir
by unknown on Apr 18, 2010 at 3:04am Add comment
Procedure on how to ResetCanon MP198 Waste ink Absorber

1. Start with printer OFF
2. Hold down STOP/RESET and then hold down POWER
3. Release STOP/RESET (don’t let go of the power just yet)
4. press STOP/RESET twice, then release POWER
5. let green light blink until printhead has finished moving.
6. Run Service Mode Tools Version 1[1].050 (DL Link http://www.4shared.com
7. Set location Set: ASA (Asia Pacific) depends on your location
8. Put paper in paper feeder Set Clear Waste Ink Choose: Main&Plater
9. Test Print Click Cleaning1 Button
10.Clear Waste ink Click Main Button
11.if theres no longer activity in the printer press Stop/Reset Button.It will print waste ink status (D=000.1 Ps=000.0)
12.Click Platen Button. It will print waste ink status (D=000.0 Ps=000.0)
13. Turn off and ON printer
14. Enjoy!!!! Printer waste ink absorber counter was succesfully reset.
by Anonymous on Apr 26, 2010 at 8:29pm Add comment
Procedure on how to Reset Canon MP198 Waste ink Absorber

1. Start with printer OFF
2. Hold down STOP/RESET and then hold down POWER
3. Release STOP/RESET (don’t let go of the power just yet)
4. press STOP/RESET twice, then release POWER
5. let green light blink until printhead has finished moving.
6. Run Service Mode Tools Version 1[1].050 (DL Link http://www.4shared.com
7. Set location Set: ASA (Asia Pacific) depends on your location
8. Put paper in paper feeder Set Clear Waste Ink Choose: Main&Plater
9. Test Print Click Cleaning1 Button
10.Clear Waste ink Click Main Button
11.if theres no longer activity in the printer press Stop/Reset Button.It will print waste ink status (D=000.0 Ps=000.0)
12.Click Platen Button. It will print waste ink status (D=000.1 Ps=000.0)
13. Turn off and ON printer
14. Enjoy!!!! Printer waste ink absorber counter was succesfully reset.

Procedure on how to Reset Canon MP198 Ink Level

No solution as of now.
by Anonymous on Apr 26, 2010 at 8:38pm Add comment
bagaimana cara reset printer mp 198 yg blinking.... makasi
by unknown on May 26, 2010 at 3:40am Add comment
the orange light in the alarm indicator is still flashing. Can u help me.please ..thanks..
by Anonymous on Jun 3, 2010 at 2:52am Add comment
sore mister,aku punya problem di printer aku gak mau menjepit kertas,,dan d lcd tampil error 26,,mhn solusi utk print aku,
by unknown on Jun 27, 2010 at 3:57am Add comment
Thanks for that it helps me a lot! God bless.
by unknown on Aug 6, 2010 at 12:18am Add comment
GMN CARA MENDWONLOAD APLIKASI MP 198
by unknown on Aug 12, 2010 at 8:35am Add comment
Hi there, can somebody please help!

I have a Canon Prixma MP190. The power button is flashing at intervals of seven; the printer counter is flashing 7E2. Printer message says that my ink absorber is full! I have tried resetting but it doesn't work, printer is currently not printing at all. Please be very simple in your instructions as I am not too familiar with computer/printers. Would really appreciate so help - Thank you :-)
by cymfy on Aug 17, 2010 at 2:28pm Add comment
after clicking the CLEANING1 BUTTON from the TEST PRINT area, the printer stopped responding and the alarm button kep blinking, also, the led shows 0 while the power button is lit. what to do with this? plz respond. tnx
by duh on Aug 22, 2010 at 11:35pm Add comment
1.power ၾကိဳးျဖဳတ္ ျပီး
2.power ခလုတ္ႏွိပ္ ျပီး power ၾကိဳးျပန္တ ပ္ျပီး power ခလုတ္မလႊတ္ ပါႏွင့္
3.clear ခလုတ္ကို ၄ ခ်က္ႏွိပ္ျ ပီး power ခလုတ္ကိုတျ ပဳိင္လႊတ္ပ ါ

ကၽြန္ေတာ္ဆ ိုရင္ အေခါက္20နဲ႕30 လုပ္တယ္
အခုရသြားျပ ီ
by unknown on Aug 30, 2010 at 9:22pm Add comment
If absorbers full.. download the canon resetter and then follow the instruction there.
by unknown on Sep 2, 2010 at 4:54pm Add comment
google hay ni want to ask how to reset canon mp198 gimanasih who error 23. thanks
by unknown on Sep 15, 2010 at 7:30pm Add comment
thanks brother, its helpfull
by unknown on Nov 8, 2010 at 7:58pm Add comment
canon pixma mp198 e23, how to clear this erroe code.
thank you.
by dowell on Dec 9, 2010 at 1:54am Add comment
Hi there, can somebody please help!

I have a Canon Prixma MP190. The power button is flashing at intervals of seven; the printer counter is flashing 7E2. Printer message says that my ink absorber is full! I have tried resetting but it doesn't work, printer is currently not printing at all. Please be very simple in your instructions as I am not too familiar with computer/printers. Would really appreciate so help - Thank you :-)
by unknown on Feb 7, 2011 at 4:08pm Add comment
http://wsoffice.blogspot.com

Worked for me to clear empty ink warning once new cartridge was installed
by unknown on Feb 22, 2011 at 8:04am Add comment
Instruction by Anonymous (4/26/10 8:38 PM)works!!Thanks bro!!
by Kimithecat on Feb 24, 2011 at 8:34am Add comment
Here is the link for software to reset all in cannon pixma mp190
You must go into service mode first. To do this:
With printer turned off, hold stop/rest then power hold for couple seconds, then release stop/reset KEEP HOLDING POWER Dont let go, then while still holding power down push stop/reset twice let go of both buttons and just wait. In a few seconds it will show a zero on screen, then press stop/rest 4 times next run this software:
http://www.4shared.com/file/EFmip97o/Reset_Canon_MP190.htm

You should be able to rest permantly any function with this software. If it dosent work do it again. It worked fine for me but it took couple times. If it screws up your printer I'm not responsible but it does work for Pixma MP190 don't know about any other models. Just make sure you download reset tool for mp190. There are several other versions and they wont work. Good Luck!
by chuck_tech on Nov 30, 2011 at 10:18pm Add comment
Thanks to "Anonymous (4/27/10 4:29 AM)" for the steps and mp198 resetter. It saved me $30 and gas for going to the printer technician. More power!
by marc6100 on Dec 6, 2011 at 8:45am Add comment
My printer is no active shown display ink recognized,but same ink40 level 198series new (intack)


salauddin
by unknown on Nov 1, 2014 at 10:19am Add comment